Sync current main and companion codec changes before preserving unsupported frame rows, rendering in the entity plane, and sharing final layout metrics with placement preview.
Share source buffers across block placements and render nested content with GPU instance transforms.\n\nChunk silhouettes and compact mesh material data so large drawings stay under device buffer limits and remain responsive.
DIMLINEAR chose its measurement axis from the two extension line origins
alone, taking the longer of their x and y differences. Every line tilted
less than 45° therefore came out horizontal and stayed horizontal, no
matter where the dimension line was dragged.
The third pick is what answers the question. A linear dimension reports
the run or the rise; pulling the dimension line clear of the points above
or below asks for the horizontal distance, pulling it out to the side
asks for the vertical one.
"Clear of the points" is measured against their extent, not their
midpoint. A dimension line dragged straight up from near one end of a
long pair is still above them even though it is a long way from the
middle, and a midpoint test would call that sideways. When the location
is inside the pair on both axes it has not said anything yet, so the
longer side still decides.
Nothing else needed changing: the measurement already projects onto the
rotation axis, and the block builder already derives the dimension line
and both extension lines from it.
Closes#669
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The readout learned to write lengths as 5'-6 1/2" and angles as
N 45d0'0" E, but typed input was still a bare parse::<f64>() — a
coordinate could be displayed and not entered. Give the formatters
their inverses.
parse_length takes feet and inches separated by a dash, a space, or
nothing, with the closing quote optional, and whole-plus-fraction in
any of those forms: 5', 60", 5'-9", 5'9-1/2, 9-1/2, 1/2. A leading
minus is a sign; the one inside 5'-9" is a separator, since after feet
there is nothing left to subtract from.
parse_angle reads the mark that says which convention an angle is in —
g for grads, r for radians, d/'/" for degrees-minutes-seconds, compass
letters for a surveyor's bearing — and reads a bare number in whichever
convention the drawing is set to.
ANGBASE and ANGDIR now apply, but only where they mean something. Which
way a thing points is measured from the drawing's zero and runs the way
it says; how wide an arc opens is the same number whatever zero is
counted from. format_direction and parse_direction are the pair for
directions, and the polar readout and polar input both go through them,
so the bearing shown is the bearing accepted. format_angle stays for
sizes, where applying a base angle would corrupt the value.
The command prompts follow the same rule, each classified rather than
swept: OFFSET distance, FILLET radius, CHAMFER distances, ARRAY and
MINSERT spacing, TRACE width, HELIX, and EXTRUDE height read lengths;
the four dimension text-rotation prompts, ARRAY's total angle and
INSERT's rotation read angles. MLINE's scale and INSERT's scale factor
are left alone — a multiplier has no unit to be written in. INSERT read
both through one parse; they are now separate.
The typed variants also take a decimal comma, which a single-value
prompt has no other use for. parse_length itself does not: inside a
coordinate the comma separates the axes.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Xref merge now inserts entities in the source block's chain order and
carries SortEntitiesTable objects across (remapped to merged handles).
draw_depth_map values become [depth, half] so exploded block/xref fills
and wide-polyline band wires both compose child depth as
insert_depth + in-block rank x half, recursing into nested inserts with
the same divisor - bands and fills from one block interleave by the
block's internal order instead of stacking at the insert's single depth.
Band batches split per rank via WireModel.depth_override; thin wires
stay merged. The wire arena falls back to a full rebuild when a slab
carries mixed depths so refreshes don't flatten band overrides.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
A wide polyline with per-vertex varying widths rendered at its widest edge
(uniform-width ones were already exact). Draw the true taper instead.
`WireModel.taper_widths` carries a per-point full band width. The wire
instance (native slim + web fat) gains per-endpoint `world_hw_a/b`, and both
wire shaders interpolate `mix(hw_a, hw_b, which_end)` so each segment's band
narrows/widens linearly — depth-tested, and the linetype dash still applies.
Alignment (widths must match the tessellated points) is solved by building
both together: a new `TruckObject::TaperedLines(points, widths)`, filled by
`common::tapered_band_points` (straight = endpoints, arc = 16 samples with the
width lerped along it). to_truck routes a varying-width polyline here —
LwPolyline before the PLINEGEN split, Polyline2D at its return — while a
uniform-width one keeps the constant-band Contour path unchanged. `world_width`
stays the widest edge as the PDF-stroke + zoom-floor fallback.
Blocks fall back to the constant-widest band (`LocalWire` carries no
taper_widths).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
A wide polyline's flat band was drawn by the hatch pipeline: a solid fill
with only draw-order depth. It ignored the entity linetype (the width
"crushed" the dash pattern) and showed through 3-D geometry in a tilted view.
Draw the band from the polyline's own centre-line wire instead. A new
`WireModel.world_width` (drawing units) makes the wire vertex shader expand
the quad by `world_half_width / world_per_pixel` (clamped to a hairline), so
the band is sized in world units and tracks zoom. Because it is now a wire:
- the GPU dash shader dashes the band by arc-length — the linetype applies;
- it is depth-tested at the polyline elevation — no draw-order see-through;
- no CPU band triangles or per-dash geometry are generated.
`world_half_width` rides in `WireConst` (native, replacing a pad) and the web
`WireInstance` (loc 14); both wire shaders branch on it. The tessellator sets
`world_width` from the LwPolyline width on the Contour / SegmentedLines arms,
and the model-space fill loop no longer emits a hatch band for any LwPolyline.
Pick still uses the band polygon (`pick_tris`).
Blocks keep the hatch band: `LocalWire` carries no `world_width` (finalize
zeroes it), so a scaled insert still scales its band correctly.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Hakan Seven