Window captures (light theme, 1400 x 860) of every sample solved on the current UI; the
thumbnails that were viewport crops are now clean ui.render images like the others; the drop
test's figure at 0.1 ms reads 129 MPa.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The drop-test and impact samples have no supports, by design, yet the browser marked Loads &
BCs as the next stage with an Add boundary condition row even after they were solved.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
results.export.csv's form listed only nodes and sets, so the parameter check refused the
probe's set, at, mode and frame and the reactions' about point that the command documents.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Four field kinds in the schema, each checked and described in JSON Schema: labels (nodes or
elements, typed as 1-5, 8 with Use selection taking the viewport's picks), points (rows of
x, y, z, added and removed), multi (checkboxes: coupling DOFs, step output) and number or
auto (the deformed scale). Node and element lists, probe and Delaunay points and block
corners use them; the remaining JSON fields hold geometry-specific shapes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The context panel reads mesh.quality's reply as the counts (an area only for a surface mesh),
each metric's min, mean and max over its histogram (the bad end warm), and its worst element: a
click selects and frames it. Invalid and undetermined elements have a button that selects
and frames them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
results.export.csv runs solve.probe or results.reactions and writes their reply as an RFC 4180
CSV: a row per node (node, x, y, z and the quantities the step has, columns it does not have
left out) or per set with the total and the applied load; numbers in shortest round-trip form,
so they read back bit for bit. A stale result is refused. The results panel has Export CSV…
beside Reaction sums and under the probed node: the save picker, or the form without one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
results.contour takes range {min?, max?} (or "auto"), kept until the field changes: a
singular peak no longer squeezes the field into the bottom bands. Values above a clamped
maximum go to an extra band drawn in the over colour, split exactly at the clamp; the legend
shows that band up to the true maximum and says it is clamped. The results panel has Legend
max/min (Auto or a value), the MCP show_results tool a range argument, and headless pictures
follow the clamp too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
diagnostics.crash_reports.delete deletes one report or all. The window lists each report
(when, what, how many times) with Report…, Copy Path and Delete, and Delete All; ui.prompt
answers it over the control channel.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The README video's model as a sample: the corpus cantilever-i-beam design opened as geometry,
swept all-hex, clamped at F2:start, 1 kN on F2:top through a kinematic coupling; static step
Load. It has a Start-card thumbnail and a gallery capture; a test checks its tip deflection
against beam theory with shear.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
file.new replaces the session with an empty one: no design, mesh, definitions, results or
journal, nothing to save, the undo history empty. The File menu and Cmd/Ctrl+N run it, asking
first over unsaved changes. A sample name the app does not know (a typo, an old ?sample= link)
opens the samples to choose from, and the status names it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Persistent names grow with a design's split history; opening accepted them but mesh tags, sets
and loads capped geometry names at 256 characters. One cap (64 KiB, against hostile input)
now holds for geometry references, partitions and saved views.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
One formatter (four significant digits, thousands separators, round-off as
0) and the model's units through every results readout:
- legend title with its unit, a mode shape normalised; Max/Min with units,
clickable to show and probe the node; markers at both in the viewport
(#321, #330)
- the deformation scale field shows the scale Deformed would use, never 0,
in the shared format; true scale named (#325, #326)
- setup symbols off over results by default (Show › Loads & BCs), and then
only the shown step's (#327)
- reaction sums in the results panel however they are run: per set and in
all, force and moment with units, applied beside reacted (#328)
- the probe: U [mm], |U|, Mises, stresses and principals with units, the
label kept inside the viewport, rows in the results panel (#329)
- hiding the mesh over a plot hides the element edges, not the contours
(#317); a hidden body's contours go with it, the range follows what is
shown (#365)
- the solve summary: peaks with units, n/a rows left out, counts grouped,
internals under Details (#321, #319)
- the energies plot: axes with units, a cursor at the frame (click or drag
to move it), hover to read (#331)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- DisplayMesh::from_model_hiding leaves out a hidden body's elements (and the
nodes only they use); Session::hidden_elements names them, so the viewport,
probing and headless pictures skip hidden bodies (#365).
- A solve summary's applied and reaction totals set the round-off of
cancelling sums to 0 (#319).
- results::principal for the probe's principal stresses (#329).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- Quantity names the unit of every number the results show from the model's
unit system (mm, MPa, N, N·mm, mJ, mW, °C or K); Field::title puts it in the
legend title, and calls a mode shape normalised (#321).
- A solved step's result stays current through edits that leave what it reads
alone (Model::step_inputs: other steps and what only they use), and comes
back current on undo (#318).
- Session::step_glyphs: the symbols of what a solved step used, for drawing
over its results; no load arrows on a frequency step's modes (#327).
- Nonlinear static steps open deformed at true scale like explicit ones, and
their automatic scale is 1 (auto_scale, shared by the viewport and the
headless pictures) (#326).
- results.reactions with an empty sets list sums the step's boundary-condition
sets, as its form says (#328).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- Select: Vertices picks the design's B-rep vertices (meshed or not), and
a selected vertex is marked (#346).
- Use selection on Datum Point (vertex, edge, face, or a hole's centre)
and Reference Point (geometry.centre: a hole's centre, a vertex, nodes)
(#346, #351).
- Partitioned Mesh: Use selection takes the picked bodies as cells; the
cell list has All, None and Invert; hovering a cell's row (or its method
row) highlights the cell in the viewport (#344).
- Rigid Wall's form takes its set from the selection; the Interactions
branch lists the explicit steps' rigid walls, each opening its step
(#350).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- geometry.bodies lists each body's vertices; geometry.datum.point by
vertex takes the design's vertex names (labelled Vertex, not Mesh
vertex) (#346).
- geometry.centre: the point for what is picked: a vertex, nodes, a
hole's centre (cylindrical faces or circular edges), else a centroid
(#351).
- mesh.cells' form: the cells first, and a method drop-down per cell
(schema kind RefChoices) instead of JSON (#344).
- interaction.rigid_wall(.delete): rigid walls of an explicit step from
the Interactions tab, no longer coming soon (#350).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
SolidCraft names the pieces of a split body by stacking suffixes
(Bracket (1) (1)' (1)). On opening a design, the pieces of one body are
named <body>.1 … <body>.N, ordered by centroid, so the tree, tooltips,
forms and picks read as one part with numbered cells.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Meshes that do not tag their element edges with the design's edge names
(tet, hex, blocks) left a selected edge with no highlight while the mesh
was shown. The edge is now marked along its own polyline, which the scene
already draws over the mesh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Preetinder Kalsi