project_trimmed accepted the analytic projection within a fifth of the nearest
triangle's size; a plane face's triangles can span the whole face, so nodes in a
3 mm fillet landed on the untrimmed box planes (mesh volume = the unfilleted box).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Topology::split cuts a block at given fractions and every block chained to it
through parallel edges, orienting the fractions through the chain, so the
topology stays conforming. A certified-invalid element is reported with its
block, cell, centre and the block vertex and blocks meeting there; the mesh is
never emitted.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Each source node follows its own path (a direction or the section normal)
to the target, found by Newton on the target's tangent plane; layers are
graded by a bias; side faces, when given, hold the boundary nodes of every
layer (alternating projections at the target), and interior nodes take the
boundary-residual correction. Source nodes are kept, so a section taken from
a neighbouring mesh conforms with it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A block topology (carved grid, butterfly and seven-block sphere templates,
O-grid, extrude, connect) projected onto a body: outer block faces onto their
smooth face groups, edges onto the curve of two targets and vertices onto the
point of three by tangent-plane iteration, nodes by transfinite interpolation,
then Winslow smoothing with the boundary on the geometry and a compass search
on the worst elements.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The swept cross-section's decomposition:
- An opening with concave corners gets a layout that continues its sides to the outer loop
(side strips and corner blocks, every corner near 90°). The thin air ring round the Pi
enclosure's square pedestal was left to the free mesher, which put a node 1e-5 from the
opening's corner: edge ratio 341,515.
- A piece's score is capped by its quadrilaterals' aspect against their longest edge or the
target size, so thin strips and pieces much smaller than the elements no longer score as
square blocks; the free mesh is scored alike for "do no harm".
- A disk is not cut into wedges round its centre (its O-grid is the scheme).
- Cuts whose pieces cannot be given division counts together (mapped pieces round a hole that
chain back to a longer side) are refused, instead of failing the whole cross-section.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
hex_mesh_swept_cells lays out one cross-section for several cells: every
cell's walls (its cut faces included) are imprinted together, every cell's
levels are levels of all, one interval assignment and one set of layers,
and each region of each level interval is filled by the cell it lies in.
Cells meet node for node across every cut, T-junctions included.
mesh.cells sweeps the cells of each design body together first and meshes
cell by cell only what does not sweep together (saying why); the reply
gives every cell's volume, scaled Jacobian and edge ratio.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Four triangles round a point (a square cut along both diagonals) share their
free half-diagonals in pairs, so those alone cannot make every loop even when
the square's perimeter is odd; the parity repair kept raising them until the
step cap. A loop that keeps coming back now lets its coupled curves move.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
fieldcraft_model::progress: a host installs a Progress on the worker thread
and reads its snapshot from another; the engine names the step being solved,
the nonlinear solver its load factor, the explicit solver its time, the
fluid solver its steps, transient heat its increments and the tet mesher its
stage and pass. Without one installed every report is a no-op (#322, #357).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Delaunay refinement split a boundary face edge at its midpoint even when that
midpoint lay inside the diametral sphere of a feature edge beside it. Each such
split halves the face vertices' distance to the curve, so they piled up against
it (the heated bracket grew face vertices 0.016 mm from a 4 mm-sized edge), the
improvement schedule could not lift the tetrahedra there to its target, and
inserted vertex after vertex around them: 29257 elements and about two minutes
to open instead of 23641 and 6 s. The SolidCraft pin move (4c91f9b) added one
interior vertex to the bracket's end faces, which changed the CDT enough to
expose it.
Following Shewchuk (1998), an encroaching midpoint now splits the encroached
feature edge instead.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A region of an extrusion's (or revolution's) cross-section that no
structured scheme fits is now cut by straight lines into blocks that fit,
before interval assignment, so the cuts are curves of the arrangement and
their counts are assigned with the rest; nothing reaches the model
(hex::decompose, after Tam and Armstrong's medial-axis subdivision and Li,
Armstrong and McKeag's primitives).
Per region: several holes are separated by lines across the gaps between
neighbouring holes; a piece with one hole gets the O-grid layout whose
pieces score best (lines from the outer corners towards the hole or along
their bisectors, from the hole's corners, or along four directions from
the hole); pieces without holes are cut by a two-ply search over lines
from concave corners and fillets and from convex corners. Candidates are
scored by meshing the pieces with their schemes (smallest corner scaled
Jacobian). A region's blocks are kept when fair (at least 0.5) or no worse
than its free mesh, and cuts never end inside a seeded curve.
This replaces the cuts from reflex corners along an edge. Tests on an L,
a T, a plate with a hole, with a slot and with three holes, and the half
crank's cross-section: every region structured, the quads conforming and
the smallest corner scaled Jacobian bounded. The half crank arm now
extrudes in 12 structured regions with a hex20 minimum scaled Jacobian of
0.37 (the arm meeting the bosses 20 degrees off tangent bounds it) where
it had 2 free regions and 0.009.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The schemes, interval constraints, curve nodes and region meshes of a
multi-level sweep's cross-section move out of layered::mesh into
hex::section, with the curve placement (seeds, projection onto walls)
passed in, so the cross-section can be meshed on its own.
region::mesh_structured gives a scheme's mesh or None where it would fold,
without falling back to the free mesher. No change in behaviour.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A cross-section region with three corners (a fillet's quarter disk, a
pocket corner cut off by a partition) was left to the free all-quad
mesher. It now gets midpoint subdivision's triangle primitive (Tam and
Armstrong 1991; Li, Armstrong, McKeag 1997): lines from a centre to a
node on each side split it into three mapped blocks, the interior then
smoothed and every quadrilateral checked (a fold falls back to free).
Interval assignment gains dominance constraints (a side shorter than
the other two together) so the split always exists.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
`quality::conformity` checks a solid mesh for cracks: the free faces must
close up (every corner edge on exactly two), no two distinct nodes may
coincide, and every element edge has one mid-side node. The hex tests
assert it for every method, hex20 included, and the crank arm sample's
7274 hex20 is conforming (#260: the disjoint lines are a display issue).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The seed's spacing becomes size-field samples the field grades from, and
after coarsening its nodes are put on the feature curve and pinned, so the
edge has exactly the seeded divisions at the seeded spacing. The quality
report gives, per seed, the boundary edges along it.
Part of #230.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A seed is matched to a mesher's curve by position (ends and middle within the
two tessellations' tolerance), which also orients its bias. Interval
assignment holds exact seeds, raises minimums and takes free seeds as goals;
an equality, loop minimum or parity it cannot meet with the exact seeds held
names them. Seeded curves get the seed's spacing. Extrude and revolve seed
cross-section curves and the layers of a level interval; sweep and mapped
seed their B-rep edges; cells seed the shared edge once, so both cells keep
it and stay conforming.
Part of #230.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
fieldcraft_mesh::mirror reflects a region's tet4, tet10, wedge6, hex8 and hex20
elements across a plane. The copies list their nodes in reflected order (corners
swapped, mid-side nodes following their edges), so every copy is right-handed;
reflected_faces and reflected_edges give the copy's face and edge over the same
nodes. Copies of the nodes on the plane are merged with the originals through
join::merge_coincident, so the region and its image form one conforming mesh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Model::merge_nodes replaces merged nodes by their survivors in elements (node
order kept, so face and edge tags hold) and in set node lists, moves a vertex
tag to an untagged survivor, and refuses a merge that would collapse an
element. fieldcraft_mesh::join::coincident_nodes / merge_coincident find the
nodes within a distance of a lower-labelled survivor, deterministically.
Meshing cell by cell and mirroring use them; node merging commands will too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A face boundary vertex lying (within the weld distance) on an undivided edge of
the neighbouring face splits that edge's triangle. Only edges no other triangle
uses are looked at, so closed surfaces are unchanged. The half of a crank arm
cut on its symmetry plane tessellates with such a junction where the cut face
meets the top face; it now meshes (tet and swept hex).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The end-to-end demo met a raw-CDT sliver that the validity gate accepted (exactly positive) and
the solver refused. Now:
- One validity criterion, `fieldcraft_model::admissible_jacobian` (normalized Jacobian above
1e-12), used by the implicit solver (fem `positive_inverse`), the explicit tet4/hex8
kinematics and the mesh gate, which proves it on the whole element (tet4: the solvers' own
Jacobian; curved kinds: a Bernstein floor), so whatever passes the gate passes the solvers.
- CDT rounding repaired by flips on the rounded mesh (Diazzi et al. 2023 §5.1) instead of the
±2-ulp nudge.
- `fieldcraft-mesh::tet`: a mutable tetrahedral complex whose every change is a checked
replacement (positive and admissible tetrahedra, faces matched with opposite orientation) with
an exact undo log; edge removal (Klincsek), multi-face removal, Delaunay insertion with
boundary faces, edge collapse; a curvature- and thickness-graded size field; constrained
Delaunay refinement with encroachment splits; ODT smoothing; the Klingner–Shewchuk schedule;
boundary vertices moved onto the exact B-rep surfaces at the end; tet10 with mid-edge nodes on
the geometry.
- `mesh.tet.generate` gains size, order, quality, quality_target, curvature_angle, grading,
max_passes, max_points and reports the CDT's and the mesh's quality; `solve.probe` takes a set
and reports its largest von Mises stress.
- Oracle cases filleted-bracket-fillet-stress(-coarse): the fillet's peak von Mises stress on
tet10 meshes of 2k and 13.5k elements, 213.3 MPa (a four-level study stays within 1.8%); the
CDT cases keep the raw tetrahedralization.
- Corpus quality columns: all 20 valid parts mesh and pass the gate.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
`fieldcraft_mesh::octree::octree_hex_mesh` meshes any closed part with hex8 only:
- an adaptive 3-refinement grid (27-tree) with strong balance and closure, filled with
conforming node-marking transition templates (Schneiders; checked over all 48 symmetries);
- a core of grid cells kept clear of the boundary (the HybridOctree buffer rule), with
non-manifold cleanup and a genus check against the part;
- a feature graph from the B-rep (corners, curves, patches) and a partition-first map of the
core's boundary onto it, then two boundary layers: a padding layer and a pillow per patch,
so every face boundary and sharp edge is captured by element edges;
- a Garanzha-type untangling and fitting energy (shape term |J|^3/chi, a volume term and a
soft fitting term, deterministic across platforms), a compass search on the worst
elements and a certified repair; failures refine the grid near them and rebuild, within
bounded attempts and growth.
The output passes the certified Jacobian check of every element and a gate that the
boundary encloses the elements' volume; boundary quads carry their B-rep faces. Quality is
reported with the same scaled Jacobian as mesh.quality. Literature notes for each step are in
docs/meshing/literature.md (B1.6-B1.10).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
hex_mesh_cells meshes cells that meet face to face (SolidCraft split
bodies) as one conforming all-hex mesh: each cell a mapped block after
smoothly meeting faces are joined (virtual topology: the halves of a hole,
a plane running into a fillet), vertices, edges and faces shared by
identity, interval assignment over all cells, each shared face meshed
once, radial edges graded off curved faces. finish spans several cells:
tags per cell, hex20 mid-edge nodes shared across cells, a closed
2-manifold boundary and no free internal face.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
Crates fieldcraft-*, binaries fieldcraft and fieldcraft-cli, the .fieldcraft file (format tag
fieldcraft/1, manifest fieldcraft.json), FIELDCRAFT_* environment variables, the MCP server
name, egui widget ids (fc_*), the app icon document FieldCraft.icon and its generated family,
docs and licences. No compatibility shim: no files of the earlier name exist.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* mesh: one transfinite interpolation for mapped hex and mesh.block; stable oracle report
mesh.block's lattice is now built from the structured hex mesher's
transfinite code: faces by quad::transfinite_grid, the interior by the new
quad::transfinite_volume (Gordon-Thiel, blended by the block's graded
parameters), which hex::mapped now calls too. 2D patches are the
transfinite_grid of their sides. Edge curves return their corners exactly.
Oracle: a zero-reference quantity (rounding noise) keeps its absolute
tolerance as its fixture band, and docs/oracle.md shows such noise and
relative errors inside the fixture band as bounds, so the report no longer
changes with the order of floating-point operations (it failed the
'docs/oracle.md is current' check on main after #50). Scordelis-Lo moved by
1.4e-9 relative (an ill-conditioned thin shell of solids: sub-ulp node
changes) and is re-blessed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* simplify: shared face filling and lattice index; faces blended like the volume; exact ends for every edge
quad::transfinite_faces fills a block's six faces (with a per-face hook
that hex::mapped uses to project onto its B-rep faces) and
quad::lattice_index fixes the lattice layout for all three users.
transfinite_grid_blended blends faces by the block's graded parameters, so
faces and interior use one parametrisation and mesh.block reproduces its
earlier Gordon-Hall lattice (the Scordelis-Lo fixture is back to its
blessed value). Straight edges also return their corners exactly.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Structured hex meshing: multi-level extrude and revolve, one-to-one sweep, mapped blocks (M5)
modelcraft_mesh::hex::hex_mesh meshes a face-tagged boundary surface with
hexahedra by the first structured method that fits: a straight or
rotational multi-level sweep (imprinted cross-section arrangement, cuts at
reflex corners, mapped/annulus/free regions), a one-to-one sweep through
rings of linking faces (least-squares affine layers with residual
correction), or a mapped logical cube (trivariate transfinite
interpolation). Interval assignment couples shared curves; boundary quads
carry B-rep face tags; the certified validity gate, a tiling check and a
fidelity check guard the output; hex20 mid-edge nodes go onto the faces.
Shape::face_surfaces exposes the analytic face surfaces; the corpus runner
gets a structured hex column.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* mesh.hex.generate: structured hex meshing as a command
Meshes one body, every body of the open design or an imported surface,
replaces the mesh, tags element faces with the B-rep faces (so sets by
geometry resolve) and reports per body the method, counts and quality.
The quality pass certifies each element once and feeds the validity gate
(quality::validity_gate_checks). Shape::size gives the cached body size
for defaults instead of a full measure.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Hex: disk O-grids, convex interval cost, early size guard, hex20 corpus column
Smooth single-loop sections (cylinders, tori, vases) get a butterfly O-grid
instead of the free mesher; interval assignment raises counts by the
squared relative error so equal sides share increments evenly; a mesh far
beyond the element limit is refused before any work and mapped limits are
no longer swallowed. The corpus reports hex8 and hex20 quality.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Catalogue: structured hex commands ready (mesh.hex.sweep, mesh.hex.mapped, mesh.hex.generate)
mesh.hex.sweep and mesh.hex.mapped run mesh.hex.generate with the sweeping
methods or the mapped one; mesh.hex.generate is the sweep entry's related
command. The planned M6 octree entry moves to mesh.hex.octree (its icon
renamed with it). docs/features.md regenerated.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Docs: structured hex literature (B8), architecture, roadmap, parity; corpus hex column
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Hex: simplify review fixes
Prepare each sweep frame's cross-section once (arrangement, cuts, fill)
and reuse it across refinement retries; candidate frames come from one
setup pass. Edge triangles come from the feature edges, layer counts go
through size::edge_divisions, sweep residual weights are computed once
per node, flux shape functions live on the stack, and the arrangement's
exact side test and distances serve the region probe. The engine takes
the boundary options mesh.tet.generate takes and names unnamed faces by
index like it; the corpus hex20 run reuses the winning method; the
mapped entry lists mesh.hex.generate too; the octree icon is redrawn
under its new id.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md and docs/meshing/corpus.md after rebasing
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md and docs/meshing/corpus.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md and docs/meshing/corpus.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md and docs/meshing/corpus.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Regenerate docs/features.md after rebasing onto main
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A four-sided planar patch at z = 0, meshed by the Coons transfinite
interpolation of its edges for plane stress, plane strain and axisymmetric
sections: the elements fill a named face of the body, edges and corners
carry names, patches join edge to edge (the join check treats the edges of
2D elements as their sides).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
Weld and face-to-face check move from the mesh.block command to
modelcraft_mesh::join (bounding-box-limited weld, grid-binned hanging-node
test), for node merging and imports to reuse. mesh.block and
mesh.tet.generate share fresh_labels. The block map evaluates each edge
curve once per lattice parameter; vector helpers come from vec3; tet10 and
hex20 mid-side nodes follow ElementKind::edges. Session::run_script returns
each step's output, which the oracle reads instead of its own loop.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
A structured mesh of a six-sided block from its corners, with circular
and elliptical edges (Gordon-Hall transfinite interpolation), grading,
named faces, edges and vertices as geometry tags, and joining to the
existing mesh face to face (refused otherwise). solve.probe takes "at"
points and reports the nearest node with a result.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Model, fem and decks: point masses, rotary inertia, springs, dashpots and rod3 trusses
Model: PointMass and Spring definitions (spring | dashpot; to ground or
two-point; along a degree of freedom, a vector or the line of the ends) on a
set or reference point, resolved per node; ElementKind::Rod3. fem: rod2/rod3
truss kernel on Basis::Line2/Line3 declaring ElementDofs (translations).
Decks: Abaqus T3D3, MASS, ROTARYI, SPRING1/2/A, DASHPOT1/2/A; Nastran CONM1,
CELAS2, CDAMP2; LS-DYNA ELEMENT_MASS/INERTIA and ELEMENT_DISCRETE; what a
format cannot take is reported. Commands model.mass.* and model.spring.*.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Implicit solver: trusses, point masses, rotary inertia and springs on the DofLayout
Trusses declare their translations like solids; point masses, inertia and
springs ask the layout for the kinds they need at their nodes (translations,
rotations), and reference points they use get six degrees of freedom. The
matrix pattern takes rows for those points; dashpots are ignored with a
warning. Existing results are bit-identical (hash-checked).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* Explicit solver: trusses, point masses, springs and dashpots on the node-major layout
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* docs: fem.md on trusses and discrete elements in the layout; regenerate features.md
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* docs: trusses in plane models and corotational explicit trusses
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* test: hostile-params test runs under small session work caps
Session gains Limits, the defaults of mesh.tet.generate's max_steiner and
max_tets (production values unchanged; a parameter still overrides them;
file.open keeps them). The registry-wide hostile-params test runs on
sessions with small caps, so the needle-triangle tessellation it meshes is
refused at once instead of meshing to the 50k Steiner cap: the engine test
binary drops from ~350 s to ~20 s locally.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* ci: move heavy tests to a heavy job on main, nightly and on demand
Four slow tests are #[ignore = "heavy: ..."] (every corpus recipe, the
cantilever convergence study, the explicit-vs-modal cantilever period, the
generic-predicate rational cross-check); fast representative tests of each
area stay in the PR gate. cargo xtask test --heavy runs every ignored test
(benchmarks included) and the doc tests; cargo xtask test and ci run the
rest without the doc tests. The new heavy CI job runs it on pushes to main,
nightly and on workflow_dispatch. Branch jobs restore main's rust cache and
no longer save their own. AGENTS.md documents the rule.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* test: the three slow LBM verification cases run in the heavy job
The Stokes-drag sphere array, the staircase-pipe convergence study and the
developing-channel case are heavy (21 s, 11 s, 6 s alone); plane
Poiseuille, Couette, Taylor-Green, reproducibility and the stability
limits stay in the PR gate.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Model: planar section kinds with Extent, element edges in sets, edge-weighted 2D loads,
centrifugal load, 2D model checks. fem: Plane kernels on Basis::{Tri3,Tri6,Quad4,Quad8}
declaring ElementDofs::new(DofSet::PLANE); QM6 incompatible modes with the
Wilson-Ibrahimbegovic correction. Solver: Kernel enum on the DofLayout; 3D results
bit-identical (hash-checked). Decks: Abaqus CPS/CPE/CAX, Nastran membranes and RFORCE,
LS-DYNA ELFORM 12/13. Mesh: free triangle mesher, planar region meshing, face boundaries.
Engine: mesh.planar with tagged edges. Analytic verification suite in solver/tests/plane.rs.
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* mesh: boundary surface preparation (weld, manifold and orientation checks, exact self-intersection, feature edges)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* engine: mesh.surface.check on an open design's body or an imported surface
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* engine: struct-init the test session
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* surface: weld at an absolute distance too; the engine welds CAD tessellations at twice SolidCraft's linear tolerance
Faces of a SolidCraft tessellation carry their own copies of shared boundary points, which agree
only to within the kernel's tolerance (up to ~2e-6 mm on the test corpus).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* docs: surface preparation in the literature survey, architecture and roadmap
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* surface: simplify after review
- The weld distance travels with the mesh (SurfaceMesh::weld_distance, set by Shape::tessellate),
so every consumer welds a tessellation correctly without opting in.
- Exact tests are infallible on predicates::orient2d_projected (shared with generic_orient2d), and
compute each vertex's plane side once per pair with an early reject.
- One Box3 for the weld, the BVH and shells; a Half struct for edges; the weld's two lookups share
one loop, with chained grid cells; cached normals for feature edges; shared parameter helpers.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* corpus: boundary surface preparation as a corpus stage
20 of 21 parts are valid boundaries with their expected genus; cross-cylinders' tessellation has
cracks and flipped triangles where its two intersection curves meet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* mesh: element quality metrics and a certified Jacobian validity check
Bernstein-form Jacobian determinants for tet4/tet10/wedge6/hex8/hex20, certified
by bounds and subdivision (Johnen-Remacle-Geuzaine 2013); Shewchuk 2002 tet
metrics, Knupp 2001 hex/wedge/quad metrics; quality report and the validity
gate meshers run on their output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* engine: mesh.quality command; model documents its node order
mesh.quality reports certified validity, volume and per-metric statistics with
fixed-range histograms. The model's ElementKind doc states the Abaqus/VTK node
order and that deck code reorders formats like Nastran CHEXA20.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
* quality: simplify after review; exact orient3d for tet4; gate on raw mesher arrays
- tet4 validity from the exact orient3d of the input coordinates
- validity_gate_elements takes (label, kind, coordinates) straight from a mesher
- one Jacobian per solid; certify caches piece bounds; product weights precomputed
- model::check_coordinates shared by set_node and quality; ElementKind is Ord
- engine: shared labels() parameter parser
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NmAttHhUZTokgPeEJia8sm
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
