OneCAD-Simulation/docs/examples.md

Examples

Every example is a built-in sample: open it from File ▸ Samples (or the start screen), with fieldcraft --sample NAME, or with the file.sample command ({"name": "drop-test"}), then press Solve (solve.run). Each opens fully defined — geometry, mesh, materials, boundary conditions, loads and steps — in mm, t, s, N and MPa, and opens and solves within half a minute. The geometry is our own: SolidCraft scripts run when the sample opens (a recipe from tests/corpus or one written in crates/engine/src/sample.rs). Each sample has a test in crates/engine/src/sample.rs that opens it, checks it clean, solves it and holds its result to the check given below.

Drop test (drop-test)

An aluminium L-bracket (60 × 40 mm foot, 50 mm upright, 8 mm thick, R6 fillet) falls 2 m onto a rigid floor tilted 15°, so the end of its foot strikes first. Explicit dynamics for 1 ms with gravity: 1 911 swept hex8 elements (one-point, stiffness hourglass control), bilinear plasticity (yield 240 MPa), the floor a rigid wall. About 8 400 increments, a few seconds.

Look at: the frames from the strike (Results ▸ Frame): the compression wave leaves the struck corner and the upright's inertia bends the fillet, where von Mises peaks near 130 MPa — below yield, so the drop leaves no permanent set. The energies plot shows the kinetic energy turning into vibration with a balance under 0.01 %.

Check: the mass equals ρ V of the bracket (0.5 %); it meets the floor at √(2 g h) = 6.26 m/s, with ½ m v² = 1 748 mJ of kinetic energy (1 %); energy is conserved (balance < 1 %); by 1 ms the floor has taken about half its downward momentum.

Rubber seal (rubber-seal)

A rubber gasket ring (20 mm inside radius, 30 mm outside, 10 mm high) squeezed 2.5 mm (25 %) between two plates bonded to it. Generic rubber, E = 6 MPa, ν = 0.49, Mooney–Rivlin with C01 = 0.2 MPa; 1 000 hybrid (u–p) hex8 elements in four mapped quarter blocks. Nonlinear static with large deformation: Newton–Raphson in nine increments, under a second.

Look at: the deformed shape at scale 1 — the free inner and outer walls bulge out, and von Mises peaks (about 7 MPa) where the bulge meets the bonded plates. Results ▸ Increment steps through the converged increments.

Check: the same ring between frictionless plates compresses evenly, and its force matches the closed form for an incompressible Mooney–Rivlin solid in uniaxial compression, P = 2 (λ − λ⁻²)(C10 + C01/λ) per original area: 3 430 N against 3 466 N (within 3 %). Bonded, the bulge makes it stiffer (shape factor 0.5): 6 518 N, held between 1.05 and 2.5 times the frictionless force. The groove and the plates are prescribed displacements today; with implicit contact (#161) the ring will be pressed by contact against a groove.

Flow past a bracket (flow-past)

Air (ρ = 1.2 kg/m³, μ = 1.8 × 10⁻⁵ Pa s) at 25 mm/s past the same L-bracket standing on the floor, the upright's back to the wind. A 240 × 120 × 100 mm box of 2.5 mm cells (184 320), uniform inlet, outlet at zero pressure, a no-slip floor and slip walls at the sides and top; D3Q19 lattice Boltzmann (TRT) for 16 s, about 6.7 flow-throughs, ten frames. Reynolds number 83 on the upright's 50 mm height: laminar, a steady wake. About 10 s.

Look at: the step's report (solve.fluid, or Results after Solve): the force on every named face of the bracket and on each side of the box, final and time-averaged, and the mass history; solve.probe with points gives the velocity and pressure in any cell, and with forces each face's force history.

Check: the drag on the bracket, as a coefficient on the upright's frontal area (40 × 50 mm), is 2.3 — a bluff plate standing on a wall at low Reynolds number in a box it blocks by 17 %, held between 1 and 3.5 (a flat plate broadside to the flow is about 1.2 at high Reynolds number and rises as it falls); the lattice's mass changes by less than 1 %.

The picture shows the bracket only: the viewport does not draw flow results yet (velocity slices and streamlines are planned in M12), so the results are numbers for now.

Heated bracket (heated-bracket)

The corpus filleted bracket (tests/corpus/filleted-bracket: an 8 mm L-bracket, R6 fillet, a hole through each leg) in steel, both hole bores clamped. The end of the upright is held at 120 °C by a heater; the rest of its outside loses heat to still air at 20 °C (h = 10 W/(m² K)); steel conducts with k = 50 W/(m K), expands with α = 12 × 10⁻⁶/K and is stress free at 20 °C. One coupled temperature–displacement step (steady) on about 23 000 tet10 elements (the count differs a little between platforms): about 5 s to open (meshing) and 13 s to solve.

Look at: Contours ▸ Temperature: the upright stays within a few degrees of the heater and the foot falls to 95 °C, a steady balance between conduction and the air. Contours ▸ Von Mises shows the stress of the growth the clamps hold back: tens of MPa through the legs, peaking at the edges of the clamped bores, where a rigid clamp is a stress singularity (about 1.5 GPa there, a figure that grows as the mesh is refined: read the stress a little away from the bore).

Check: the temperatures lie between the air's and the heater's and fall away from the heater. For the expansion, the test puts the air at the heater's temperature, so the bracket warms evenly by ΔT = 100 K, and clamps the foot's hole alone: the bracket then grows freely about it, and a point moves α ΔT times its distance from the hole's axis. The upright's top moves −0.0432 mm along x (within 2 %); the foot's end, 16 mm from the clamped bore, which cannot grow, moves 0.0228 mm against 0.024 mm (within 6 %).

Hex-meshed bracket (bracket-hex)

The same filleted bracket split into 30 cells in SolidCraft (tests/corpus/filleted-bracket-blocks: planar cuts through the legs and diagonal cuts round the holes and the fillet, each cell a six-sided block), meshed by mesh.hex.blocks as one conforming all-hex mesh: 5 778 hex20 elements of 3 mm, O-grids round the holes, graded through the fillet, every shared face meshed once. Steel; the upright's end clamped, 1 kN down on the foot's end. Linear static: about 2 s to open (the cells are rebuilt from the script) and 3 s to solve.

Look at: the mesh (Prepare ▸ Mesh) — mapped blocks meeting face to face with no pyramids or tets — and the von Mises contours (tick Deformed for the deformed shape): the stress runs round the fillet and peaks at 295 MPa at the upright's hole.

Check: the tip of the foot moves 0.509 mm down, within 1 % of a 48 016-element tet10 solution of the unpartitioned part (0.5093 mm, crates/testkit/tests/bracket_blocks.rs), and the clamp carries the whole 1 kN.

Mirrored crank arm (crank-mirror)

The model of crank-arm under the name of its mirror workflow (the sample kept so scripts and links made with it still open): seen from below, where the pocket is. How the half is cut, meshed and mirrored is told under crank-arm.

Look at: the pocket from below: straight mapped rows along its sides and floor, and at each end its corner fillets as three-sided triangle primitives, cut off by the mesher's own blocks; the two halves, mirror images across the arm's middle.

Check: as crank-arm.

Bicycle crank arm (crank-arm)

A 170 mm aluminium crank built in SolidCraft (crates/engine/samples/crank-arm.json): a 16 mm arm tapering from 38 to 24 mm, root arcs into a Ø46 × 22 spindle boss with a 12.7 mm square bore (R1.5 corners) and a Ø30 × 20 pedal boss with a Ø14 hole, and an 82 × 14 × 8 pocket in its back (R5 corners). It is a stack of extrusions along z, so it sweeps all-hex. To keep it sweepable the hex variant leaves out the pocket's floor fillet and the bosses' 1.5 mm chamfers, and its root arcs meet the bosses about 20° off tangent (a tangent meeting leaves a zero-angle cusp on the arm's top face, where any hex is degenerate). 6061-T6 (E = 68 900 MPa, ν = 0.33); the square bore's faces fixed, 1500 N on the pedal hole in the crank's plane, across the arm (−y). Linear static: about 5 s to open and 7 s to solve.

The mesh needs one datum. A datum plane on the symmetry plane (Sym, y = 0) partitions the crank (Half); mesh.hex.generate extrudes the half CrankArm/a (hex20 of 3 mm) and cuts its cross-section into mappable blocks itself, inside the mesher (nothing is added to the model): the half ring round each bore as four-sided blocks, the pocket's R5 corners as three-sided triangle primitives, and four-sided blocks along the arm, split where the pocket's fillets meet it. Interval assignment gives every block's sides matching counts, with no seeds. mesh.mirror reflects the half onto CrankArm/b: 8 664 hex20 elements, all valid, scaled Jacobian min 0.37 (at the corners where the root arcs meet the bosses 20° off tangent), mean 0.91. Before the mesher cut blocks itself the same crank took seven partitions and eleven exact seeds for 0.37 (and the swept half without them: min 0.009, its middle free-paved).

Look at: the mesh (Prepare ▸ Mesh): rows running straight along the arm, the O-grids round the bores, eight layers through the arm, and the von Mises contours: the bending stress grows along the arm toward the root; the peak, 117 MPa, sits at a square-bore corner where the rigid clamp meets the free face, a support singularity.

Check: σxx on the arm's sides at x = 29 mm is −62.44 and +62.44 MPa, equal and opposite as the mirror-image halves are, against the beam formula M/Z = 1500 · 141 / (16 · 35.6² / 6) = 62.6 MPa (0.25 %); a 41 815-element tet10 solution of the full part gives 62.3 MPa. The pedal bore moves 0.75 mm down (tet10: 0.70–0.75 mm; Euler–Bernoulli with a rigid clamp: 0.58 mm, without shear or the boss's compliance), and the spindle carries the whole 1500 N and 255 N·m.

Cantilever (cantilever)

A steel beam of 160 hex8 elements, clamped at one end with a load on the other: a static step and a frequency step. Look at: the bending stress, highest at the clamped root, and the Modes step's mode shapes.

Bar impact (impact)

The same beam flying onto a rigid wall: an explicit dynamic step of ten frames. Look at: the stress wave running back along the bar (Results ▸ Frame) and the energy history in the Results panel.

Hex and tet parts (parts)

A hex8 block beside a tet4 cube: meshes to look at (element types, nodes, picking), nothing to solve.

I-beam cantilever (ibeam)

The 200 mm steel I-beam of the README video (tests/corpus/cantilever-i-beam), opened as SolidCraft geometry with persistent face names, swept all-hex (hex8 of 4 mm, incompatible modes), clamped at F2:start and loaded with 1000 N down through a kinematic coupling to F2:top. Look at: the bending stress in the flanges, highest at the clamp; the tip moves 0.18 mm down (beam theory with shear: 0.184 mm).