Mesh edges that do not evaluate without a panic; refuse such boolean results (#1252) (#1364)

The mesher samples edges through a fallible evaluation, so an intersection curve whose projection fails to converge no longer panics; a boolean result with an edge that does not evaluate is refused with an error. Fixes #1252.

crates/kernel/src/intersection_curve_tests.rs

@@ -58,3 +58,59 @@ fn open_intersection_keeps_endpoints_on_both_planes() {
     assert_eq!(curve.subs(hi), end);
     assert_eq!(curve.subs((lo + hi) / 2.0), Point3::new(2.0, 0.0, 0.0));
 }
+
+/// A triangular face whose first edge is an intersection curve of two planes: the parallel planes
+/// `z = 0` and `z = 1` when `support_gap` is `1.0` (the projection onto both never converges), the
+/// same plane twice when it is `0.0` (the leader lies on both and always evaluates).
+fn triangle_with_intersection_edge(support_gap: f64) -> truck_modeling::Shell {
+    use truck_modeling::{Curve, Edge, Face, IntersectionCurve, Leader, Line, Shell, Surface, Vertex, Wire};
+    let plane = |z: f64| Surface::Plane(Plane::new(Point3::new(0.0, 0.0, z), Point3::new(1.0, 0.0, z), Point3::new(0.0, 1.0, z)));
+    let (v0, v1, v2) = (Vertex::new(Point3::new(0.0, 0.0, 0.5)), Vertex::new(Point3::new(1.0, 0.0, 0.5)), Vertex::new(Point3::new(0.5, 1.0, 0.5)));
+    let leader = Leader::Polyline(PolylineCurve(vec![Point3::new(0.0, 0.0, 0.5), Point3::new(1.0, 0.0, 0.5)]));
+    let bad = IntersectionCurve::new_unchecked(Box::new(plane(0.5 - support_gap / 2.0)), Box::new(plane(0.5 + support_gap / 2.0)), leader, 0.01);
+    let line = |a: &Vertex, b: &Vertex| Edge::new(a, b, Curve::Line(Line(a.point(), b.point())));
+    let wire = Wire::from(vec![Edge::new(&v0, &v1, Curve::IntersectionCurve(bad)), line(&v1, &v2), line(&v2, &v0)]);
+    Shell::from(vec![Face::new(vec![wire], plane(0.5))])
+}
+
+/// Meshing an edge whose intersection curve does not evaluate (#1252): `IntersectionCurve::subs`
+/// unwraps a failed projection, and the mesher sampled the edge through it. The two supports here
+/// are parallel planes, so the projection never converges. Nothing may panic (wasm aborts on one,
+/// and the native guard prints the message first) and the mesh stays finite.
+#[test]
+fn meshing_an_edge_that_does_not_evaluate_neither_panics_nor_goes_non_finite() {
+    use std::sync::Arc;
+    use std::sync::atomic::{AtomicUsize, Ordering};
+    use truck_meshalgo::prelude::RobustMeshableShape;
+    let shell = triangle_with_intersection_edge(1.0);
+
+    let me = std::thread::current().id();
+    let count = Arc::new(AtomicUsize::new(0));
+    let c2 = count.clone();
+    let prev = std::panic::take_hook();
+    std::panic::set_hook(Box::new(move |_| {
+        if std::thread::current().id() == me {
+            c2.fetch_add(1, Ordering::SeqCst);
+        }
+    }));
+    let meshed = std::panic::catch_unwind(std::panic::AssertUnwindSafe(|| shell.robust_triangulation(0.01)));
+    std::panic::set_hook(prev);
+    assert_eq!(count.load(Ordering::SeqCst), 0, "panics while meshing");
+    let meshed = meshed.unwrap();
+    for face in meshed.face_iter() {
+        if let Some(mesh) = face.surface() {
+            assert!(mesh.positions().iter().all(|p| p.x.is_finite() && p.y.is_finite() && p.z.is_finite()));
+        }
+    }
+}
+
+/// A boolean's result with an edge that does not evaluate is refused with an error (#1252). The
+/// mesher's panic on such an edge used to reject the attempt; now that it no longer panics, the
+/// result must be refused explicitly or a plausible-looking mesh would let it through.
+#[test]
+fn a_result_with_an_edge_that_does_not_evaluate_is_refused() {
+    use truck_modeling::Solid;
+    let solid = |gap: f64| Solid::new_unchecked(vec![triangle_with_intersection_edge(gap)]);
+    assert!(!crate::boolean_record::edges_evaluate(&solid(1.0)));
+    assert!(crate::boolean_record::edges_evaluate(&solid(0.0)));
+}