Rectangular and circular sketch patterns stay linked to their source: editing the pattern's count, spacing or the source geometry updates the copies, and the copies keep their point and radius relations. Patterns are saved under format 20; older designs keep their independent copies.
Edges shorter than the model tolerance are dropped from the flat cells, and the refold sews touching corners, so a cut-out across a bend line no longer fails with a degenerate edge.
doc.open and the STEP/mesh imports run on the file loader's worker with the request's path scope, and a font named by file path in a design is checked against the scope before it is read.
Moves the per-feature geometry handling (transforms, face points, profile selections, point expressions) into one geometry walk in feature_geometry.rs, with a golden record of what each feature kind moves. sheet.perforate holds no world geometry and joins the no-op arm.
Where an Import's stored labels pair one for one with its numbered built bodies (X, X (2), X (3)), component.paste_new stores the copy under the bodies' names, so the copied features after it find their bodies. No format change.
sketch.text and sketch.edit_text make the curve a text follows construction in the same undo step, so it no longer cuts the letters into pieces; the reply names the curve as guide.
timeline.paste keeps a cylinder Emboss's persistent face name, remapped onto the pasted features and bodies, so the copy embosses the pasted cylinder instead of failing (#1035).
Adds sheet.perforate: round holes on a staggered or square grid over the flat sheet, kept clear of edges, cut-outs and bend zones. The holes go to the flat pattern, the DXF and the measured volume rather than the B-rep, so a panel can carry many thousands of them.
Adds local scalar appearance and material libraries: a catalog in the io crate with safe writes, engine commands to list and apply library entries, and a library dialog in the UI, with docs.
Thin Extrude builds walls of a set thickness along sketch curves, open chains and closed loops, with the wall centred, inside, outside or on both sides at two thicknesses. Saved under format 20 (thin on an Extrude); an extrude without thin saves as before. Closes#721.
Part 2 of #876: one walk over the references a feature holds (the sketches it's built from, the features it names, the bodies it works on) replaces three hand-written matches, with a golden record covering every variant.
Bodies imported with the same label come in as X, X (2), X (3). Renaming one of them no longer renumbers the others: body.rename now pins the current names of the feature's other bodies when it stores the new one, so later renames, materials, appearances and features still find them.
A tapered extrude now offsets spline and conic curves as well as lines and arcs, so sketch text and any other profile can take a taper, and the join of tapered letters onto a face finds its boolean result.
sketch.text and sketch.edit_text took at, height, angle and text with a silent default when a value had the wrong kind, so a height of "H" made 5 mm text and at: ["H", 25] put it at the origin. An input that is given (not null) now has to be what it names, or the command is refused with the input's name, and a null at no longer passes as the origin.
A planar union no longer leaves a sliver where an edge crosses its neighbour, so a sheet whose outline runs on past a flange's edge with a slight bend unfolds again.
timeline.export_script (and solidcraft-cli script) writes a design's history as a command script that solidcraft-cli eval replays into the same design, so a bug that only shows on one design becomes a one-file repro. timeline.add restores one stored feature with its id, names and references, through the same checks a design file gets when it opens.
Closes#886. SychPL's #1078 approached the same issue independently; thanks to both.
Co-authored-by: SychPL <SychPL@users.noreply.github.com>
On Windows the temporary folder often has an 8.3 short name, which the path scope refuses. vfs::long_names spells folders SolidCraft derives from the environment with long names, and the MCP scratch folder and the recovery folder use it, so screenshot without a path and the recovery commands work there again.
Pasting an Import together with later features that name its bodies now points those features at the pasted copies, including bodies whose names carry a number such as X (2).
* feat: validate physical material cards with sources and conditions
* feat: query directional elastic modulus from physical material cards
* fix: register physical material validation labels in complete locales
* fix: register directional elasticity labels in complete locales
* Add German and Korean labels for the material property commands
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Convert to Sheet Metal without bend edges refused every plate whose bounding-box diagonal reached a thousand times its thickness ("no outline on that face"), and just under that limit a hole smaller than the mesh's sag fell out of the outline and the DXF. The outline's tolerance is now at most a tenth of the thickness: a thin plate is meshed again at that tolerance. Nothing new is stored. Tests: long thin strips, sheets thousands of times longer than thick, and a strip keeping holes down to 1 mm.
* Fillets and chamfers meeting at corners on curved faces, on top of #935
What #935 and #926 leave of #851 and the matrix:
- Corner build for blends meeting on faces of any surface (curvecorner.rs):
the knife-edge tip's round with the arc's or the back edge's, edges
picked in any order, a round ending in an earlier round of its radius
(as a feature of its own), and chamfers meeting at the arc's corner.
Its end curves are fitted by chord length: a uniform parameter
through points clustered at the ends doubled back on itself there,
and the display planner refused the face.
- A straight edge ending at a curved face (the back edge into the
knife-edge tip): rolled, or cut by the face in the planar corner
build (blend_corner.rs).
- A rolling ball turning about a rounded corner of its own radius
(a pivot: a piece of sphere or cone).
- Seams that are an earlier blend's straight contact (fitted curves)
count as straight.
- No spline across a joint where the strip's curvature jumps (a line
into a small round): each strip ends on the joint's section.
- Sections at a chain's vertices on the faces of the edge from it
alone.
- Every new fillet path passes #949's check for openings.
Tests measure volumes through the display plan, as #935's do.
Action matrix: 51 more fillets and chamfers pass (sweep, tangent arc
chain, sheet-metal hem, bracket holes), none fewer. Robustness seed 33
recorded (its last fillet builds differently; display and measured
volumes now agree).
Co-Authored-By: bherbruck <brennen.herbruck@gmail.com>
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_015bV2ntwLfUHV4JnCMPSyRi
* Corner blend tests: scale, seed 33's volumes, tighter engine bounds
From the review of #854:
- seed_33_display_plan_and_measure_agree: seed 33's bodies measure
the same through the display plan and the measure (2e-5), which the
golden's re-record rests on.
- the_arc_rounded_after_the_back_edge_matches_both_together: the order
that still leaves 0.05 mm³ at the tip, as an ignored test.
- corner_blends_hold_at_any_scale: the cases this branch adds on the
#851 part, at 0.01x and 100x, take off what they take at full size
times k³ (within 5e-6, checked to 1e-4).
- The engine tests on the part as drawn measure through the display
plan; bounds are about twice what each reads (2e-4 to 3e-3), and the
front corner's sets are checked against the kernel's CSG grid.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_015bV2ntwLfUHV4JnCMPSyRi
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Adds the read-only material.properties.validate command: schema_version 1 engineering material cards in SI units are checked for numerical consistency and elastic stability, with derived isotropic moduli, missing conditions and sources needing review. Nothing is assigned or saved.
Thanks @0xlillith.
Fixes#971. At the node limit the offset certificate splits the fitted curve where it meets the exact offset midpoint, so curves with different parameter speeds certify within the same 0.002 mm tolerance. Associated offset fit nodes are hidden from display, picking, box selection and snapping until Break Association.
Thanks @Karl-VonRichter.
Fixes#928. Extrude To / From Object and Revolve To Object now resolve their target in the feature's own component frame, so a face in another component whose occurrence is moved is found where it is shown instead of the extrude stopping at a flat plane through the picked point. The point is named after the nearest face, a named point keeps its named face when another component touches it there, and such features re-evaluate when a placement changes, so they follow the target when it moves later.
Co-authored-by: SychPL <SychPL@users.noreply.github.com>
Fillet gets a Curvature (G2) radius type (type: "curvature", alias "g2"): a quintic blend whose size is the equivalent circular setback, for convex and concave straight edges between planar faces with a perpendicular planar end face at each end. Unsupported cases are refused rather than falling back to a circular fillet, and a blend that would cross a loop in its end face is refused. Persisted as a fillet style under format 19; labels in en/de/ja/ko/zh.
Co-authored-by: midasdf <midasdf@users.noreply.github.com>
Trimming the base at an edge flange's setback snaps corners within tolerance onto the trim line and merges away the zero-width run a ledge as tall as the setback left along it, so the ledge goes with the strip as a lower one does. Splitting outline edges at other cells' corners now skips points within the model's tolerance of an end, so a ledge a little taller keeps its sliver and the bend runs under it, also off the axes. Both used to fail with "sew: a degenerate edge". Nothing new is stored.
A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Holes on round faces from the app, one hole per pick, and Flip for holes at sketch points (#967)
The Hole dialog takes any face: a hole on a round face drills against the face's normal where it
was picked, and its arrow shows that. A round face split at its seam is picked whole, but makes
one hole where it was clicked. Holes at sketch points get Flip (saved as flip in the hole's points,
under format 18), in the command and in the dialog.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Holes at sketch points show their arrow: into the part, or away with Flip (#967)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Sketch Mirror, rectangular and circular Pattern, and Offset now show a green live preview that follows the selection and settings; OK commits, Cancel leaves the sketch unchanged. The shared dialogs show the current selection step and source counts, sources can be toggled with Ctrl/Cmd-click, cleared and reselected.
Offsets keep editable driving distance dimensions (One Side, Two Sides, Symmetric) that update the derived curves without moving the source, with undo/redo and save/reopen. Format 19: older files keep their fixed offsets.
New dialog labels in en, zh, ja, de and ko.
Fixes#696. Fixes#517.
The plate check compared the face outline's area (from the tessellation, so each hole was a polygon of chords) with the exact volume, and refused plates with a few small holes. Where the outline runs along a cylinder about the plate's normal it is now an arc of that circle; coaxial pieces of one radius are one wall, so a hole split into two, three or four faces is one circle. The check passes with its tolerance unchanged, and the flat pattern and its DXF carry one CIRCLE per hole (ARC for rounded corners and slot ends).
A round blank now converts too, so unfold_cut_refold_and_convert checks the refusal with a block thicker at one end instead of a rod.
* Hole matrix: placement, types, extents, edits and 0.9.0 designs, with today's failures listed
Each case checks the drill goes into the material, the bore sits on its axis, a blind hole stops
where it should, the removed volume against its analytic value, the face count and that every
body is still one closed valid solid. Failing cases are listed in tests/hole_matrix/known_failures.txt
as a ratchet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* A hole on a face drills into the material, also in older designs (#950)
Without a direction, solid.hole took the direction from any face whose infinite plane passed
within ten tolerances of the point, the last one found winning: the far side of a thin plate or a
face of another body at the same height could set it, and the wrong direction was saved. It now
uses the face nearest the point, against its outward normal (exact for planes, cylinders and
spheres, so holes on curved faces work without a direction). When a design is evaluated, a face
hole whose saved direction leaves the face it starts on is mirrored into it, so designs saved
with the wrong direction drill into the part.
Fixes#950.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Hole at a point on no face (a planar face's centroid outside it) keeps the plane it lies in
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Record the hole direction fix in the goldens and the action matrix baseline (#950)
Seeds 7, 21, 81 and 85 drill their holes straight into their faces now. In the action matrix,
holes on four faces that used to go the wrong way now build, and two whose correct direction
meets a cut the kernel refuses are marked failing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Goldens: seeds 7, 21 and 85 drill their holes straight in (#950)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
- A fold's zone clipped across the root of a tab folded before on the same
line kept a sliver of no width there, which made the zone look like it
crossed a slanted edge. The one real piece is the zone now (#638).
- When the tabs a fold line spans can't take the side beyond them along,
because it joins the side that stays through other material (a tab on the
inside edge of an L, the fixed point on the far leg), the tabs' own ends fold
instead, the same part as with the fixed point on the near leg (#639).
Co-authored-by: jonaswre <3731681+jonaswre@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Name a side drawn on several sketch curves by all of them
An extrude named each side wall after the one sketch curve its profile
segment lies on. A wall along two coincident lines (squares drawn edge to
edge) or along collinear lines merged into one profile segment had no
single curve, so it was named from geometry and could not carry a sketch
attachment. One sketch extruded up and down and joined (the logo) refused
a sketch on every one of its side walls.
Such a side is now named by every curve it lies on, in sketch order: the
first is its name, the others aliases. The set is fixed by the sketch, so
the name is exact. The refusal message no longer blames merged faces.
Adds the reported logo design and a synthetic up-and-down join to the
action-matrix designs, and a regression test that sketches and extrudes on
every flat face, fresh and after save and reopen.
Fixes#954
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix: record the up-and-down join designs
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
- A new cut was clipped against the panel with every one of its cut-outs, so
each hole of a perforation cost the square of all the holes before it and the
second cut of 500 ran out of the flat budget. A tool is now clipped against
only the cut-outs whose boxes meet its own (the same result).
- The planar booleans' point-in-loop test now skips loops whose box is clear of
the point, before the costly on-the-loop test; with a thousand holes that test
was most of the time.
The 1000-hole panel now takes about 15 s instead of failing.
Co-authored-by: jonaswre <3731681+jonaswre@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
On a large thin sheet the probes around the fixed point stepped clean through
the sheet (twice the mesh tolerance of a 465 mm part is more than its 0.8 mm
thickness), so a point exactly on the face touched no material and the fold
was refused. The probes now also step a quarter of the thickness.
Co-authored-by: jonaswre <3731681+jonaswre@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Rounded Rectangle sketch tool (#891)
A new SKETCH > CREATE command, sketch.rectangle.rounded, in the Rectangle
family: two opposite corners and a corner radius make a 2-point rectangle
whose four corners are filleted alike, as one undo step. The radius is one
parameter (one radius dimension, the other arcs equal to it), so changing it
changes all four corners. While drawing, Width, Height and Radius boxes take
typed values; typed width and height dimension the overall size between
opposite sides. Without a typed radius the corners get a fifth of the shorter
side.
Fixes#891
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Rounded Rectangle in the Simplified Chinese catalog
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Session::replace_design keeps auto_project when file.new, doc.open and doc.recover swap in another design, and the UI keeps it across tabs, adopt and the last-tab close. Regression tests in engine (sketch_project) and ui-egui (documents).
Offsets picked faces along their normals into a new surface body: planes and cylinders move exactly, other faces get a fitted B-spline within tolerance, and offsets that would fold over are refused. Adds the SurfaceOffset feature (noted under format 18), the surface.offset engine command and an Offset Surface dialog.
Closes#758.
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
A design with components and joints exports as a URDF robot description (file.export to .urdf, the MCP export tool, solidcraft-cli run --out, File > Export URDF...). It writes one binary STL per component in metres, links with mass, centre of mass and inertia from material density, and maps rigid, revolute, slider, cylindrical, pin-slot, planar and ball joints to URDF joints or short chains. Loops, broken joints and loose parts are reported as warnings. Options: mesh_prefix, effort, velocity. Docs in docs/urdf.md.
Each wall of a surface built from sketch curves (Surface Extrude, Revolve, Sweep and Loft) is now named after the curve it comes from, exactly rather than from geometry, so references to those faces survive edits.
Surface Loft lofts open or closed curve chains, one section per sketch in pick order, into surface bodies. Adds the SurfaceLoft feature (format 18 note), the surface.loft command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Sweep carries open curves and closed profile boundaries along a sketch path into surface bodies, with smooth walls along curved point paths. Adds the SurfaceSweep feature (format 18 note), the surface.sweep command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Revolve turns open curves and closed profile boundaries about a sketch axis into surface bodies, with cone apexes and sphere poles where a chain ends on the axis, and a closed shell made solid. Adds the SurfaceRevolve feature (format 18 note), the surface.revolve command, a dialog with Edit Feature support and analytic kernel and engine tests.
Part of #757.
A lip picked on a face that isn't a shelled body's rim, such as the Sample Plate's top
face with its two holes and the boss standing on it, ran its band round the largest inner
edge. That was the boss's foot, so the band stood against the boss's wall and the join
failed with a boolean error about curved faces.
The band now goes round the face's opening (an inner edge with no material just over the
face inside it). A rim face that has a smaller hole in it still works. A face whose inner
edges are only where other features stand on it, or whose openings are alike in size (a
plate's holes), is refused with a plain message that names the rim face it needs.
Fixes#892.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Hole centres from a sketch now drill into the material on whichever side of the sketch plane it lies: material the spot starts in wins, then the nearest body ahead, else against the sketch normal as before. A sketch on a part's underside or below it now drills up into the part. Covers counterbores, through-all, edge and corner centres, patterns and reopening.
Delete Face takes heal (default true, as before). With heal: false the picked faces are removed and the gap stays open, leaving the remaining faces as a surface body (kernel remove_faces); deleting every face is refused. Saved only when false, noted under format 18.
Display meshes after opening, the face names read when a feature finds a face by name, and inspect.measure over all bodies are now worked out per body on plain scoped threads (solidcraft_kernel::for_each_on_threads / map_on_threads), in body order and with the same results; the browser build stays serial.
Karl Von Richter