A cut-out made in the flat pattern could cross a bend only with edges
running along the bend or square to it: a round hole or a slanted slot
over a bend line failed to fold ("not supported yet: curved cut-outs
across a bend", "... cut-out edges running across a bend at an angle").
Sheet: a flat edge in a bend zone now folds whichever way it runs: along
the bend to a line, across it to an arc, and any other way to a curve on
the bend's cylinder (a slanted line to a helix). The curve is carried as
a chain of cubic Hermite pieces fitted within 1e-7 mm on both faces of
the sheet, with breaks that depend on the flat edge only, so the top
face, the bottom face and the wall share them. The wall between the two
chains is a ruled surface with radial rulings: the cut-out's wall stays
square to the sheet. The bend's own faces stay exact cylinders, now sized
to the whole boundary of their cell (a curved edge may bulge past its
corners).
Kernel: such an edge has no line, arc or conic form, so the sewing
interface gets EdgeSpec::Chain (a chain of cubic Bézier pieces: a cubic
B-spline with triple inner knots, its ends on the shared vertices) and
SurfSpec::Ruled (two chains joined by straight lines, so a wall built
from the chains holds them exactly). The sheet module's rev_edge becomes
EdgeSpec::reversed, so the new variant is handled where edges are
reversed.
The test for "along" and "across" is in millimetres (1e-6 mm at the
edge's ends) instead of relative 1e-9, so coordinates rounded by a script
fold as drawn.
Tests. Kernel: a box with one wall bulging as a cubic (chains of two
pieces at the bottom and the top, the wall ruled between them) sews to a
valid solid of the analytic volume, 27.6 (measured 27.59965); chains with
the wrong number of control points, a NaN or too many pieces, and a ruled
wall between chains of different piece counts, are refused. Sheet: a slot
turned 30° and a round hole across 72°, 90° and 108° bends fold to valid
solids that lose the cut-out's flat area times the thickness (K = 0.5:
400 and 100.53 mm³, measured within 0.02); a slanted flat edge folds to
its exact helix within 1e-7 mm (measured 1.9e-8) on both faces; lines
along and across the bend keep their line and arc. Engine:
fold_through_cut_outs now expects a round hole across a fold to fold, and
to unfold to the same round hole; the per-bend machining guard (#296)
sews a bend that carries a round cut-out, so a hole beside it cuts and a
hole in the bend is still refused.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* fix(doc): extrude and revolve in a moved component from another component's sketch
A feature built from a sketch of another component read the sketch's plane as if it were in
the feature's own component. When the two components are placed differently (a moved or
jointed part), the tool landed transformed along with the feature's component: a join on a
part turned half a turn about Z, from a root sketch, came out on the far side of the origin.
Extrude and Revolve now see the sketch through both placements, as sweeps along 3D paths and
sketches on another component's face already do (sketch_in_feature_frame, using
profile_in_frame). The sheet-metal rotated-frames test built its cap witness from a sketch of
the moved component while the root was active, relying on the old reading; it now builds the
witness in the sketch's own component, which is what it measures against.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* test: To Object extrude in a moved component from a root sketch
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* style: rustfmt
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Edge flanges meeting at a corner of the base were closed only at exactly
90°; at any other angle they stayed open (a V at 72°) and the rule's gap
was not used.
The flanges of one feature now close at any convex base corner and any
bend angle: each panel end is cut square to the sheet on a line in the
flat (slanted off 90°, stored as ext plus a new per-end slope) so the
edges nearest each other, on the inner faces, run parallel the rule's gap
apart about the plane bisecting the inner faces. The construction reads
the two flanges' own angles, so it holds for unequal ones as well. At 90°
it is the extension the old code gave (reference case 69-sm-tray is
unchanged). A corner that can't close (a gap under 0.01 mm, flanges
bending opposite ways, ends that would overlap in the flat pattern) stays
open, and the flange feature reports a warning that says where and why.
A flange of a later feature leaves the corner as it was (reference case
75-sm-bracket-holes: the earlier flange keeps its length).
Tested at 72° and 90° against a hand derivation, on a trapezoid, and
every 5° from 45° to 135° on a rectangle and a trapezoid (gap exact, one
flat region without hairline edges, one valid shell holding the flat
material).
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The guard that refuses machining through bends sewed every bend zone and
nonparallel panel into one solid. Two bends meeting at an open corner relief
share only an edge, so that sew failed with "nonmanifold edge contact" and any
cut on the base was refused. Sew and test each piece on its own instead.
Reference case 75-sm-bracket-holes now passes; its known_failure mark is removed.
Fixes#296
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A sheet-metal tray built at 2000 x 2500 mm with an edge flange on all four
edges (72° or 90°) and unfolded failed to rebuild when W and H went to
400 x 300, 600 x 450, or W alone to 400: "planar region arrangement failed
or exceeded its bounded processing budget". The same tray drawn at 400 x 300
unfolded, and growing it worked.
The sketch solved again after the change leaves its corners ~1e-13 mm off,
so the flanges inherit a hair of tilt and their panels and bend zones meet
the trimmed base within 1e-13 mm instead of exactly. The flat pattern is a
balanced union of those pieces, and the arrangement chains its output loops
within 10 tol. In a later round, ray parity classified a bend zone's edge
midpoint that lay level with a corner whose two lines did not quite meet:
the ray slipped through the gap without a crossing, the zone's edges counted
as inside the other operand and were dropped, and the outline no longer
closed. A rectangle turned by 1e-14 rad failed the same way.
inside_loop now closes the gap where one line ends and the next begins with
a straight connector while it counts crossings; exactly closed joints are
unaffected. Joints with an arc keep the arc's own endpoint rule, which
treats ends within its angular tolerance as on the ray (a connector there
double counted at a circle split into two arcs).
Co-authored-by: NOWN-DEV <257771410+NOWN-DEV@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* test: reproduce #264 (Sheet metal: collinear tabs cannot be folded or flanged together)
* fix(sheet): fold and flange tabs that sit side by side on one line (#264)
A fold's bend zone and a flange's setback were cut with an infinite line, so
a second tab on the same line blocked a fold ('slanted or curved edge') and
two tab-end flanges in one feature shared one trimmed edge (nonmanifold).
When the zone falls apart into pieces, fold only the pieces the fold points
span, each as its own bend; trim a flange's setback only from the material
along its own edge, and attach each flange to the edge it was picked on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* test: reproduce #263 (sheet.fold accepts a fixed point that is not on the sheet)
* fix(sheet): refuse a fold's fixed point that lies off the sheet's material (#263)
A fixed point inside a cut-out or outside the base outline (in the panel's
thickness) silently picked a side. Refuse it with an error that names the
point; side-face picks and points on other panels keep working.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* test: reproduce #262 (sheet.fold: bend zone reaching the blank outline is reported as a slanted or curved edge)
* fix(sheet): name the bend zone reaching an outline corner instead of blaming a slanted edge (#262)
A fold whose bend zone contains a corner of the panel outline (a fold at a
tab's root) was reported as crossing a slanted or curved edge. Name the
corner and how far to move the fold line to clear it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Record ownership transfers in the timeline so earlier Join/Cut membership,
world placement, machining data and styles survive component moves, edits,
independent copying, undo and reopening. Preserve pending positions in history
snapshots and keep constructor transfers ordered during feature redefinition.
Retain shallow sheet pockets and exact planar intersection islands through
unfold/refold, with depth-aware flat previews and DXF export. Store explicit
3D wire coordinate spaces and migrate known legacy provenance without moving
saved points or analytic fits.
Infer unique eligible cylindrical Emboss targets, align Revolve manipulators
with actual extent geometry, and discard obsolete preview errors after input
correction. Certify constructed and immutable imported face styles using exact
source metadata while preserving legacy face names. Upgrade designs to format10
with bounded validation and geometry-preserving legacy migration.
Persist typed sketch dimensions and bounded ordered configuration rules in format 8. Use exact occurrence paths and source identity for editing, movement, appearance, and mass. Preserve sheet material regions through cutting, folding, and exact DXF export; retain nested cavities and material islands.
Validation: cargo xtask ci passed, including 368 engine tests, 178 UI tests, 68 UI scenarios, 136 kernel tests, and the 10-crate wasm check. Actual preview workflows and legacy format-7 origin-corner reopening were inspected.
The old ids live only in crates/engine/src/legacy_ids.rs (the legacy migration table): find_command maps them, so old scripts, recipes and control calls keep working, and saved shortcuts, recent and pinned commands are migrated on load (designs store no command ids). Parity maps the observed catalog ids to ours through xtask/data/fusion-ids.tsv. The agent rule now reads: our own dotted id, never another product's. Cargo.toml's repository points at github.com/bherbruck/solvecraft.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
