Commit Graph
5 Commits
Author SHA1 Message Date
NOWN-DEVandClaude Opus 5.5 0d995c6a78 fix: lines and arcs that touch meet at one point in planar booleans (#432)
The planar arrangement solved a line and a circle, or two circles, for their two
crossings even where the curves only touch. At a tangent contact the two roots are
rounding noise spread along the curves by its square root: a 1e-12 mm error in the
centre's distance from the line puts them 2e-6 mm either side of the contact on a
2 mm arc, well inside the tolerance of both curves; when the noise falls the other
way there is no root at all. Cutting a rounded corner (an arc tangent to the two
edges it ends on) out of a plate with planar_regions_boolean then ran that far along
the plate's edge past the arc's end before turning onto the arc: a 200 x 37 plate
turned by 0.25 degrees came back with six edges, one of them 3.45e-6 mm long.

Curves that touch within the arrangement's tolerance now meet at the one point their
centres give: the foot of the circle's centre on the line, or the point on the line
of centres of two circles tangent inside or outside. Circles of nearly one radius
about nearly one centre keep the general formula.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-12 19:22:39 -04:00
8e0c3d2794 feat: fold sheet metal cut-outs across bends at any angle or curved (#425)
A cut-out made in the flat pattern could cross a bend only with edges
running along the bend or square to it: a round hole or a slanted slot
over a bend line failed to fold ("not supported yet: curved cut-outs
across a bend", "... cut-out edges running across a bend at an angle").

Sheet: a flat edge in a bend zone now folds whichever way it runs: along
the bend to a line, across it to an arc, and any other way to a curve on
the bend's cylinder (a slanted line to a helix). The curve is carried as
a chain of cubic Hermite pieces fitted within 1e-7 mm on both faces of
the sheet, with breaks that depend on the flat edge only, so the top
face, the bottom face and the wall share them. The wall between the two
chains is a ruled surface with radial rulings: the cut-out's wall stays
square to the sheet. The bend's own faces stay exact cylinders, now sized
to the whole boundary of their cell (a curved edge may bulge past its
corners).

Kernel: such an edge has no line, arc or conic form, so the sewing
interface gets EdgeSpec::Chain (a chain of cubic Bézier pieces: a cubic
B-spline with triple inner knots, its ends on the shared vertices) and
SurfSpec::Ruled (two chains joined by straight lines, so a wall built
from the chains holds them exactly). The sheet module's rev_edge becomes
EdgeSpec::reversed, so the new variant is handled where edges are
reversed.

The test for "along" and "across" is in millimetres (1e-6 mm at the
edge's ends) instead of relative 1e-9, so coordinates rounded by a script
fold as drawn.

Tests. Kernel: a box with one wall bulging as a cubic (chains of two
pieces at the bottom and the top, the wall ruled between them) sews to a
valid solid of the analytic volume, 27.6 (measured 27.59965); chains with
the wrong number of control points, a NaN or too many pieces, and a ruled
wall between chains of different piece counts, are refused. Sheet: a slot
turned 30° and a round hole across 72°, 90° and 108° bends fold to valid
solids that lose the cut-out's flat area times the thickness (K = 0.5:
400 and 100.53 mm³, measured within 0.02); a slanted flat edge folds to
its exact helix within 1e-7 mm (measured 1.9e-8) on both faces; lines
along and across the bend keep their line and arc. Engine:
fold_through_cut_outs now expects a round hole across a fold to fold, and
to unfold to the same round hole; the per-bend machining guard (#296)
sews a bend that carries a round cut-out, so a hole beside it cuts and a
hole in the bend is still refused.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-12 19:03:22 -04:00
NOWN-DEVandClaude Opus 5.5 f34ac5881f fix: the sheet metal flat budget counts exact lines and arcs once (#430)
The flat-pattern point budget (16 384) counted every cut-out by its 0.001 mm
chords, arcs included, so a plate with 240 round 4 mm holes (about 100 chords
each, 480 exact arcs) was refused with "sheet metal flat geometry exceeds the
bounded processing budget" when the holes were cut in the unfolded sheet. The
planar booleans work on exact lines and arcs whole, so those now count once
each; a sampled curve still counts its chords. A second limit keeps the
chords of everything, arcs included, at 65 536, the same figure the planar
boolean applies to the sampling it does itself, so the work stays bounded.

planar_region no longer samples an exact loop only to discard the result: the
complexity check right above it already covers the same budget.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-12 18:58:45 -04:00
NOWN-DEVandClaude Opus 5.5 0154572580 feat: close sheet flange corners at any angle (#406)
Edge flanges meeting at a corner of the base were closed only at exactly
90°; at any other angle they stayed open (a V at 72°) and the rule's gap
was not used.

The flanges of one feature now close at any convex base corner and any
bend angle: each panel end is cut square to the sheet on a line in the
flat (slanted off 90°, stored as ext plus a new per-end slope) so the
edges nearest each other, on the inner faces, run parallel the rule's gap
apart about the plane bisecting the inner faces. The construction reads
the two flanges' own angles, so it holds for unequal ones as well. At 90°
it is the extension the old code gave (reference case 69-sm-tray is
unchanged). A corner that can't close (a gap under 0.01 mm, flanges
bending opposite ways, ends that would overlap in the flat pattern) stays
open, and the flange feature reports a warning that says where and why.

A flange of a later feature leaves the corner as it was (reference case
75-sm-bracket-holes: the earlier flange keeps its length).

Tested at 72° and 90° against a hand derivation, on a trapezoid, and
every 5° from 45° to 135° on a rectangle and a trapezoid (gap exact, one
flat region without hairline edges, one valid shell holding the flat
material).

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-12 18:48:19 -04:00
NOWN-DEVandClaude Opus 5.5 3938e267bb fix: fail solidcraft-cli run when a timeline feature fails (#402)
A parameter change can break a feature without failing the command that
made it; parameters.change reports it only in its `errors`. `run` then
exited 0 and exported the bodies as they were before the failing feature:
a shrunk sheet-metal tray whose unfold failed came out folded, without
the holes and cut-outs made after the unfold.

`run` now checks the evaluated timeline before writing anything. Any
feature with an error fails the run with status 1, lists the failing
features on stderr and writes none of the --out and --save files, as a
failing command already does. --allow-errors writes them anyway. `eval`
is unchanged and still reports the errors in its timeline.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-12 18:45:10 -04:00