The empty design shown at launch, New on a design that is still empty, file.new and the blank design left when the last tab closes all take the Units of new designs preference. Opened files and the sample part keep their own units. Fixes#1205.
Co-authored-by: raythurman2386 <raythurman2386@users.noreply.github.com>
A symmetric solid extrude of 10 mm is now 10 mm thick, 5 mm each side of the sketch plane, and switching from One Side to Symmetric keeps the thickness entered. Under format 21 the extent records its convention; designs saved without it keep the per-side reading, so their geometry and parameters don't change. Fixes#1236.
Co-authored-by: Karl-VonRichter <Karl-VonRichter@users.noreply.github.com>
* Action matrix regressions of #1255: knuckle rounds, thin holes, a 45° flange hole, an axis after an edit
- Curve blends: past the end of a curved edge the run of sections along the end
tangent wrapped round the ring of centres; it is shortened while it still
crosses the end face (the hinge knuckle's cap rounds at 0.728 mm).
- Boolean retry guard: each body's volume is measured finer than its smallest
radius, and a volume out of bounds is measured again ten times finer before
it refuses (a 0.133 mm drill measured -30272 mm³; a plastic part's coarse
mesh was off by more than the slack).
- Sheet metal: a drill cap's certificate allows the evaluation noise its fitted
tilt shows (a hole square to a 45° flange).
- Construction geometry on a named face uses the face found by name, not a
second pick at its nearest point (an axis through a corner round after a
parameter moved it).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Retry guard: measure the target, tool and result at one tolerance
Measured at different tolerances, the chords' error on the faces they share
didn't cancel: a blind hole in a long D-profile bar measured 20 mm³ more than
the bar.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix baseline from this branch's full run: 37 actions pass again, none fewer
Blessed with cargo xtask action-matrix --from DIR --bless from the 16 shards of
run 38673859774.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix: nightly shards cut by measured cost, heavy designs in slices, and a determinism check
The full matrix ran as four fixed quarters of the corpus and two of them hit the 60-minute
job limit. Now action_matrix_shard runs shard k of n (ACTION_MATRIX_SHARD=k/n), planned from
tests/action_matrix/costs.json: designs that take more than five minutes are split into slices,
and the pieces go largest first to the least loaded shard. The nightly runs 12 shards and uploads
each one's outcomes and timings; cargo xtask action-matrix --from DIR --bless records them in the
baseline and costs.json without running the matrix again. action_matrix_determinism runs a sample
twice and lists any action whose outcome changed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix: costs measured on runners, 10 shards, determinism on the lighter designs
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix: baseline and costs from a full run on main, 16 shards, timeouts listed
The baseline is regenerated from the 10 shards' results of a full run on 01b1b705
(cargo xtask action-matrix --from DIR --bless): 8 new designs, 302 actions that pass now,
names that changed, and 40 actions that passed before and fail now, each listed in #1255
(22 fillets refused since #949, 4 hinge blends since #1101, 9 on the loft cut, 5 single).
costs.json now holds every design's measured time, and the nightly runs 16 shards of about
17 minutes. An action that passes in the baseline and times out is listed but not judged,
and stays passing when blessed: two runs of the same build differed only on 10 actions that
took 50-84 s against the 90 s limit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix: slice heavy designs by a hash of each action's name
Slicing by index gave some slices only fillets on oracle 41 (28 slices, a multiple of the
actions per edge), three times the planned time; two shards ran past their limit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The preview builds only the tool; the boolean runs once on OK, off the window thread, with a Computing label while it takes a while. Follow-up to #1020.
Lands the Render workspace (R3), bounded preview-image jobs with cancellation and atomic PNG export (R4a), and opaque PBR looks as one change.
- Render workspace: an overlay-free product preview on the installed GPU device. Returning to Design restores its camera. render.scene and render.settings.apply are added.
- Image jobs: render.preflight/start/status/cancel/export run bounded CPU preview jobs. Export captures the job, overwrite choice and document, and checks the caller's file scope before writing.
- Opaque PBR: looks can carry metal fraction, roughness and dielectric IOR. The product viewport and preview PNG use them; geometry and mass are unchanged. The v1 catalog export refuses PBR rather than dropping it.
- Render setups and PBR looks are saved under design format 21. Labels are in en/de/ja/ko/zh/ru.
Supersedes #706 and #800. Refs #620, #673, #756, #1004.
Contributed by @0xlillith.
Co-authored-by: lillith <35337584+0xlillith@users.noreply.github.com>
A crash inside a graphics driver left only "an unclean exit between
commands": no backtrace, no module, no hint that it was at startup.
- The crash journal now keeps the startup step the app is in (window,
graphics instance, surface, adapter request, adapter chosen, device
creation, renderer and viewport shader compiles, surface configure,
first frame and its present, running) and the renderer as soon as the
adapter is picked. egui-wgpu tells the app about its steps through a
small hook. An unclean exit before the first frame names the step.
- Windows: an unhandled-exception filter (src/native_crash.rs, the one
Windows-only module allowed unsafe) writes the exception code, the
faulting module and offset, and a minidump next to the journal; the
next start puts them into the report.
- The Windows CI job runs a child that faults on purpose and checks the
report.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Windows: start Direct3D 12 first, and Vulkan only without a D3D12 GPU
wgpu started Vulkan, D3D12 and OpenGL together and preferred Vulkan, so
every Windows start loaded all installed Vulkan drivers. An old Intel
Vulkan driver (igvk64.dll) crashed 0.10.1 at startup inside the driver.
The app now probes D3D12, then Vulkan, then OpenGL, one backend at a
time, and starts only the first with a hardware adapter (WARP when none
has one). WGPU_BACKEND still wins; graphics.json's "backend" sets the
order by hand; the software renderer (safe mode, the retry) uses D3D12
alone. A new Windows CI job starts the real app under several settings.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* CI: a test filter YAML parses
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* CI: the startup smoke test writes graphics.json where the app reads it
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* CI: run the WARP shader tests one at a time
WARP's shader JIT (d3d10warp.dll) crashed twice in 124 runs of the gpu
tests with four test threads, with a null read inside its own optimizer
while several devices compiled compute pipelines at once. Serial runs
did not crash.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A design built over MCP is many small commands, and each one did work over the
whole design, so building or showing a 1,300-body design took minutes:
- moved components were transformed and meshed again after every change; world_state
now reuses each placed body whose definition and placement are unchanged
- next_d_name searched the design once per candidate number
- Document::eval evaluated every parameter for every expression; now only when the
expression names one
- param_rows' used_by was quadratic; the desktop no longer gathers completions on every
change while no text box has focus
solidcraft-cli bench-agent builds a generated ~1,300-body bicycle command by command
and times it (241 s -> 16 s here). Eval output is unchanged apart from timings.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Open and Save use parented AsyncFileDialog sheets; their answers run on the UI thread in a later frame, so resizing the window while a picker is open no longer re-enters winit and aborts. Editors, tab changes, Close/Quit and model-changing control requests wait for the answer; the local library Open and Export in the Appearance dialog use the same flow. Fixes#1088.
Startup no longer stops at a bad settings file or a missing GPU: a settings file that fails to load is set aside, a failed GPU start retries with the software renderer, and a safe mode starts with defaults. Adds a troubleshooting page to the guide.
Thin Extrude builds walls of a set thickness along sketch curves, open chains and closed loops, with the wall centred, inside, outside or on both sides at two thicknesses. Saved under format 20 (thin on an Extrude); an extrude without thin saves as before. Closes#721.
Where SolidCraft can replace itself safely, the Update window gets Update now:
- AppImage: the new AppImage is downloaded next to the old one, verified and renamed over
it; Restart now starts it as SolidCraft exits.
- Windows MSI: the verified .msi starts (msiexec /i … /passive) once SolidCraft has closed,
after the usual questions about unsaved designs.
- Windows portable zip / standalone exe: the running solidcraft.exe is renamed to .old, the
new one takes its name (solidcraft-cli.exe too), Restart now; .old goes at the next start.
- macOS: the verified .dmg is opened (the app is ad-hoc signed and not notarized, so it isn't
replaced behind the user's back).
- Flatpak, Snap, deb, rpm, tar.gz: never replaced; the window shows the command.
Every package's SHA-256 must match the release's SHA256SUMS.txt (HTTPS, same release); a
mismatch deletes the download and changes nothing. With PUBLIC_KEY set in update/install.rs,
SHA256SUMS.txt.minisig must also verify (minisign-verify, MIT) with a trusted comment naming
the release. release.yml signs the list when the UPDATE_SIGNING_KEY secret exists and fails
when the app expects signatures but the secret is missing; docs/releasing.md has the steps.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Straight edges stay one edge after cuts (#1049)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Robustness goldens: cuts join straight edges along untouched walls (#1049)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* fmt
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Robustness goldens note: what each changed seed shows when replayed on both builds
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
At start, and at most once a day, a background thread asks GitHub for the latest stable
release (one HTTPS GET to releases/latest, nothing else sent; 15 s timeout; silent when
offline; GitHub's rate limit respected). When it is newer than this build, an Update button
appears next to Report a bug. It opens a window with the version, the release notes and
Download (the asset that fits this installation), Skip this version and Remind me later.
- Versions compare as semver; a nightly counts as the release it was built after, so it is
offered only a newer stable release.
- The installation is detected (AppImage, Flatpak, Snap from the store or a file, deb, rpm,
tar.gz, Windows MSI/portable/exe, macOS app); Download picks the fixed-name asset.
Development builds and the Flatpak (no network permission) never check.
- Preferences > General > Updates: Check for updates automatically (on) and Check now.
- HTTP via ureq + rustls with the operating system's certificates (desktop app only).
- docs: Updates and privacy page.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
macOS hands files opened from Finder, the Dock or open -a to the application delegate's application:openURLs:, which winit's delegate lacks, so AppKit showed "SolidCraft cannot open files in the SolidCraft design format". open_documents adds that method to the delegate's class before launch finishes and queues the paths for the UI, which opens them like files named on the command line.
This is the one place SolidCraft's own code uses unsafe: the app crate denies unsafe_code instead of forbidding it, and only the two macOS-only functions in open_documents.rs allow it, with the reason documented there and in AGENTS.md. Adapted from VectorCraft (see ATTRIBUTION.md).
Closes#997.
timeline.export_script (and solidcraft-cli script) writes a design's history as a command script that solidcraft-cli eval replays into the same design, so a bug that only shows on one design becomes a one-file repro. timeline.add restores one stored feature with its id, names and references, through the same checks a design file gets when it opens.
Closes#886. SychPL's #1078 approached the same issue independently; thanks to both.
Co-authored-by: SychPL <SychPL@users.noreply.github.com>
The sampled pi-case hole on Body1/F13:side:l7@F14.1 became a real hole with #952 (7.5 s instead of 170 ms); beside the heavy tests on main's push runs it passed the matrix's 90 s action limit in its edit round, reported as the design not loading. The sample now takes every CPU in nextest so nothing runs beside it, and the edit round writes a start line so a hang there is reported as <action>+edit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Fillets and chamfers ending on a boss's pieced wall or beside it, on a face that runs along its seam twice, and loops the loop blend refuses
- A straight edge whose end meets one curved surface in several faces (a cylinder a join left
in pieces) ends on that surface: the section is cut where it crosses each seam, which is
shortened there; where no seam is crossed (the wall missing inside the other body) the
section lies on the bared surface and the rest of the side edge becomes a seam.
- Two end faces that aren't both planes meeting in lines: each face takes the section's points
on it, cut where it crosses the edge between them. Not where an end face runs on smoothly
from a side (an earlier round): the corner build takes those.
- Face boundaries close over several connector edges.
- A face on a periodic surface running along its seam twice (as a STEP file gives it) is
rebuilt the same way (#691).
- A curved chain ending square on a face that runs on past its side extends that face's seam.
- A smooth chain stops before an edge between faces that meet smoothly.
- A loop the loop blend refuses for its shape is blended edge by edge; refusals about its size
stand.
- Action matrix: ACTION_MATRIX_ACTIONS and ACTION_MATRIX_VALIDITY for quick local runs; the
fillets and chamfers that pass now recorded.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Closing a socket with unread input resets the connection, and the reset could reach the client before the refusal did (requests_run_only_after_the_token failed 17 times in 100). The server now ends its side and drains, briefly and up to 64 KiB, what the client had sent before closing: 0 in 100.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A through-all hole's tool is twice the largest body long, and the boolean's tolerances
followed that length: a 6 mm hole through a 920 mm part was traced at nearly 1 mm, wider than
the hole, and the cut came out empty or failed. When every other strategy has failed, the
boolean is now asked again (unshifted, then once shifted) at tolerances scaled to where the
bodies meet: the overlap of their boxes and the thinner operand's thickness. Its result is
checked as the others are and held to the retry guard. It runs last, so whatever an earlier
strategy answered is kept as it was, and only for single-shell operands (bodies in several
pieces are retried a piece at a time, each with this pass of its own).
The sampled shortcut also gave up on a slender tool lying across its box (a long hole drilled at
an angle fills little of it): it now samples past the first 2000 points until enough land
inside, so a tool that misses a body leaves that body as it is. Bodies that had enough samples
in the first 2000 are sampled exactly as before.
Baseline: the 90 actions that newly pass, rechecked one by one with the final build.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The browser build fetched its Japanese fallback font only for a Japanese UI,
so a Japanese design name, file name or typed text showed as tofu with the UI
in English. After drawing each frame the web shell now looks through the
painted text for kana, CJK ideographs and full-width forms while no CJK font
is loaded, and fetches the same font once on the first hit. A failed fetch
with an English UI leaves the language alone and is not retried in a loop.
Sessions that never show such text download nothing extra.
Fixes#720
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The app's control protocol gets engine.batch: the steps run in one request (so one frame), each as engine.execute runs it, stopping at the first failure and rolling back to the checkpoint by default. The MCP batch tool sends it to a running app (with the control token), is never resent after a lost reply, and falls back to step-by-step when the app refuses (agent cursor shown, or a step loads a file). A batch may take up to an hour to answer.
Display meshes after opening, the face names read when a feature finds a face by name, and inspect.measure over all bodies are now worked out per body on plain scoped threads (solidcraft_kernel::for_each_on_threads / map_on_threads), in body order and with the same results; the browser build stays serial.
solidcraft --control PORT writes a random per-launch token to a user-only file (<data>/control/PORT.token; 0700/0600 on Unix, icacls on Windows; SOLIDCRAFT_CONTROL_TOKEN overrides) and refuses any connection whose first request lacks it. mcp --connect, the demo and packaging smoke clients send it. MCP execute/batch/open/save/export/screenshot are annotated destructive and open-world, new_design destructive. Docs: control-protocol.md, mcp.md, AGENTS.md, pending release note in releasing.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Agent tool calls (MCP, and bridged control requests carrying allow_paths) reach files only in the open design's folder (strictly inside home or the temporary folder, not in a hidden folder, and never its hidden files), the app's recovery folder, the server's private scratch folder and each --allow-path; --allow-any-path lifts the limit. Paths are resolved first, so .. and symlinks that lead out (including a save through a link, #845) are refused. On Windows, UNC, device, NT, verbatim non-drive, drive-relative, alternate-stream, reserved-device and 8.3 short-name paths are refused before any file system call, and the resolved path must be on a local drive. doc.recovery_discard and doc.recover {discard} delete only real recovery entries. Docs: mcp.md, control-protocol.md, README.
Loading a design (from a worker's start or restart to its first output) gets 300 s; each action keeps 90 s. oracle/41-tube-radial-holes (about 23 s here) timed out loading on a loaded CI runner, and reloads after a hung action were charged to the next action.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Adds oracle case 81 (a box edge rounded at a clamped cubic B-spline radius) with analytic expected values, and passes spline fillets through recipes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
truck's face and edge IDs are their addresses, so walking maps keyed by them followed heap layout, and the ribbed lid's side-wall hole passed or failed by chance. The planar boolean's rebuild and glue now take truck's connected components in the shell's order, and the planar boolean's own maps are ordered. Healing's union-find keeps the lesser root and takes a run's ends in order of use. The face classification after an intersection orders each component's faces by the shell first. The lid now builds the same body on every run, with a test that builds it six times in one process. Its 0.5 mm side-wall holes, and one sensor enclosure hole of the same kind, now fail every time and are marked failing in the baseline.
Fixes#707.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The nearest point on a triangle with a zero-length edge (a cone's tip) is no longer NaN, so an axis or tangent plane on a drill tip works again (#567).
A cut built slab by slab (the exact prism boolean) sewed the result from horizontal
slabs and only joins merged the coplanar pieces back. So a floor vent cut through the
Raspberry Pi case split the long wall into strips at the ports' tops and bottoms
(87 faces instead of 79 at 32 mm), and at 24 mm the end opening split the end wall.
- Prism booleans merge coplanar neighbours for every operation (faces only: edges,
curves and surfaces stay exact), keeping each face's construction source where all
its pieces share it, Split Face lines and regularization protection. Painted or
protected operands keep their authored pieces as before.
- The prism history now tells apart a wall's several edges with its caps (a wall
with openings meets each opening's floor), so cuts beside existing openings keep
exact history and faces keep their names.
- Tests: the Pi case's faces pinned after every feature at 24, at 24 changed to 32,
and built at 32 (each outer side one face); random openings and bosses on a
shelled case never split another side; every corpus design rebuilds a parameter
edit like a fresh build and reverts exactly.
- Action matrix baseline: demo/pi-case re-blessed (fewer, merged faces; no
regressions), demo/pi-case-0.8 recorded, and 88 new passes on
regressions/lid_ribs_flush_with_window.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Sheet metal rims and bend ends attach by name (<panel>:rim.<edge>, <flange>:rim.bend0/1), as do face profiles from sheet faces. A plain or counterbored Hole square to a panel is machined into the flat pattern. Boss, Lip, Rest and Snap Fit keep the body's history and name their own faces. Hole tools name their faces by the part they cut, and pattern copies as copies. A pattern's repeated fillets keep the body's history. Loft sides are named by their section curves. A piece Offset Face moved off its face's plane attaches by its own qualified name. Sides of a profile grown to overlap a flush body keep their sketch line's name, so walls a Join merged take a sketch (#681). Face sketch 75% -> 90%, offset plane 75% -> 90%, press-pull/extrude 64% -> 85% in the action matrix; baseline blessed.
Fixes#494, fixes#495, fixes#560, fixes#561, fixes#563, fixes#564, fixes#681.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Joining ribs flush with a lid's window left a zero-thickness slit far from the rib (the planar fallback glued back only one of the faces its pieces shared) and displaced the tool on the other joins. Gluing now joins every shared face pair, coincident-face separation checks there is material behind a pushed face for every join, and any join or cut that needed a retry must be closed, keep volume monotonic and leave the part unchanged outside the tool's box, or it is refused with an error. Feature command replies carry the feature's warning.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A single edge's blend no longer needs a plane square to the edge at each end. Straight edges: each rail ends where it reaches the end face's surface, the side edges there are shortened or continued along their line or circle, and the blend ends where its cylinder or chamfer plane meets that surface (a fitted curve checked against both). A chamfer may end across two faces. Curved edges: at a slanted or curved end the rolling ball runs on past the end and the strip is cut back where it meets that face. A straight edge running smoothly into a bend or rounded corner is blended along its whole smooth chain. Rolling-ball fixes: smooth chains follow edges stored against their curve, the ball touches only the faces of the edges it rolls along, the seam normal at a joint comes from the face there, and each strip is fitted with neighbouring sections at its own spacing.
Action matrix: edge.fillet 83.6% -> 93.0%, edge.chamfer 82.6% -> 93.3% (697 new passes, no regressions); reference tests 76/76.
Fixes#556
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Body::new no longer turns a long thin solid (a through-all hole's tool) inside out on the strength of a coarse mesh volume: it checks again on a fine mesh first. 79 more face.hole actions pass in the action matrix; the remaining no-result cuts stay under #559.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A flat face that no construction certificate names on its own now attaches by its exact history name (a new lineage face certificate): cut walls and floors, chamfer faces, each pattern or mirror copy, side walls a Join merged, and the pieces a later feature split a face into. Construction certificates still come first; a seed keeps its certificate when it is patterned. Two flush extrudes of one outline joined end to end keep their exact history in the prism boolean. Face sketch 52% -> 71%, offset plane 52% -> 71%, press-pull/extrude from face 41% -> 60% in the action matrix; baseline blessed.
Fixes#491, fixes#492, fixes#493, fixes#557.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Flatpak app id, desktop/metainfo/MIME file names, icon name and the window's Wayland app_id / X11 class are now ai.storyteller.solidcraft, the id the ArtCraft launcher expects.
Existing Flatpak installs move over: the Pages repo marks app/ai.storyteller.solvecraft end-of-life with a rebase to the new id, so flatpak update offers the switch and Flatpak carries ~/.var/app along. A new install next to the old one copies settings and autosaves on first launch through a read-only grant on the old data folder. The metainfo declares <replaces>/<provides>, the desktop entry X-Flatpak-RenamedFrom, and AppImages drop the menu entry an older AppImage installed. deb/rpm upgrades remove the old-named files.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Hidden bodies, occurrence placements, sketches and origin items are saved with the design and come back when it is reopened. Visibility is still not an undo step, but hiding or showing something now counts as an unsaved change. Additive field under format 16. Fixes#531.
Co-authored-by: jonaswre <jonas.wrede@beyondit.gmbh>
Construction axes, points and planes resolve their picks against the model as their component sees it (in the root, every placement, pasted instances too), and a Hole picked on another component's body cuts that body. components-arm 355 -> 502/594 and joints-hinge 304/390 -> 371/408 in the action matrix.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Refs #303. file.save / file.save_as can store a warm native geometry cache (cache: true, off by default) keyed to the document hash, app version and adapter revision. Opening shows a bounded preview from it until the rebuilt session replaces it. Any cache failure counts as a miss.
apps/solidcraft-cli/tests/action_matrix.rs tries sketch, offset/angle/mid planes, press pull, extrude from a face, hole, draft, shell, fillet, chamfer, axes, points, planes, projection, move, copy, mirror and pattern on the final bodies of 104 designs (the old design files, the examples, the 76 reference recipes, the enclosure demos, the Pi case built through the UI, eight typical parts), through the commands and picks the desktop sends, each design in its own process, with an edit round on a sample of passes. tests/action_matrix/baseline.json is a ratchet: an action that passed there and fails now fails the test; newly passing ones are reported for cargo xtask action-matrix --bless. Every CI run checks a fixed sample; the nightly Action matrix job runs the whole matrix in four parts. 30,567 of 35,576 actions pass (85.9%); results and causes in docs/action-matrix.md, one ignored reproduction per open cause (#556-#568).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
solid.move takes copy: true to keep the source bodies and transform a new copy of each, with a Create Copy box in the Move dialog. Designs without it save and load exactly as before.
A profile traced over a face sketch's projected boundary left the extrude's caps and sides without an exact planar source, so a sketch or offset plane on the new top face was refused. The drawn curve is now the edge's source where it covers a projection. Clearer fixed-plane message; regression tests in the engine, UI harness and design corpus, plus a corpus-wide flat-face attachment check (known gaps under #491-#495).
Fixes#489
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* docs: add OpenGraph and Twitter card tags to the book and web app
Links to the docs site and the browser app now unfurl with a preview card.
The book gets the tags through theme/head.hbs (og:title follows the page
title); the web app's index.html carries its own, pointing at /app/. Both
use the social preview image, now served from the book at /solidcraft/og.png.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HWLPLy7ug7URSK5WybjRNa
* docs: list the social preview image in ATTRIBUTION.md
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HWLPLy7ug7URSK5WybjRNa
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
