Persistent names grow with a design's split history; opening accepted them but mesh tags, sets
and loads capped geometry names at 256 characters. One cap (64 KiB, against hostile input)
now holds for geometry references, partitions and saved views.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
One formatter (four significant digits, thousands separators, round-off as
0) and the model's units through every results readout:
- legend title with its unit, a mode shape normalised; Max/Min with units,
clickable to show and probe the node; markers at both in the viewport
(#321, #330)
- the deformation scale field shows the scale Deformed would use, never 0,
in the shared format; true scale named (#325, #326)
- setup symbols off over results by default (Show › Loads & BCs), and then
only the shown step's (#327)
- reaction sums in the results panel however they are run: per set and in
all, force and moment with units, applied beside reacted (#328)
- the probe: U [mm], |U|, Mises, stresses and principals with units, the
label kept inside the viewport, rows in the results panel (#329)
- hiding the mesh over a plot hides the element edges, not the contours
(#317); a hidden body's contours go with it, the range follows what is
shown (#365)
- the solve summary: peaks with units, n/a rows left out, counts grouped,
internals under Details (#321, #319)
- the energies plot: axes with units, a cursor at the frame (click or drag
to move it), hover to read (#331)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- DisplayMesh::from_model_hiding leaves out a hidden body's elements (and the
nodes only they use); Session::hidden_elements names them, so the viewport,
probing and headless pictures skip hidden bodies (#365).
- A solve summary's applied and reaction totals set the round-off of
cancelling sums to 0 (#319).
- results::principal for the probe's principal stresses (#329).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- Quantity names the unit of every number the results show from the model's
unit system (mm, MPa, N, N·mm, mJ, mW, °C or K); Field::title puts it in the
legend title, and calls a mode shape normalised (#321).
- A solved step's result stays current through edits that leave what it reads
alone (Model::step_inputs: other steps and what only they use), and comes
back current on undo (#318).
- Session::step_glyphs: the symbols of what a solved step used, for drawing
over its results; no load arrows on a frequency step's modes (#327).
- Nonlinear static steps open deformed at true scale like explicit ones, and
their automatic scale is 1 (auto_scale, shared by the viewport and the
headless pictures) (#326).
- results.reactions with an empty sets list sums the step's boundary-condition
sets, as its form says (#328).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- Select: Vertices picks the design's B-rep vertices (meshed or not), and
a selected vertex is marked (#346).
- Use selection on Datum Point (vertex, edge, face, or a hole's centre)
and Reference Point (geometry.centre: a hole's centre, a vertex, nodes)
(#346, #351).
- Partitioned Mesh: Use selection takes the picked bodies as cells; the
cell list has All, None and Invert; hovering a cell's row (or its method
row) highlights the cell in the viewport (#344).
- Rigid Wall's form takes its set from the selection; the Interactions
branch lists the explicit steps' rigid walls, each opening its step
(#350).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- geometry.bodies lists each body's vertices; geometry.datum.point by
vertex takes the design's vertex names (labelled Vertex, not Mesh
vertex) (#346).
- geometry.centre: the point for what is picked: a vertex, nodes, a
hole's centre (cylindrical faces or circular edges), else a centroid
(#351).
- mesh.cells' form: the cells first, and a method drop-down per cell
(schema kind RefChoices) instead of JSON (#344).
- interaction.rigid_wall(.delete): rigid walls of an explicit step from
the Interactions tab, no longer coming soon (#350).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
SolidCraft names the pieces of a split body by stacking suffixes
(Bracket (1) (1)' (1)). On opening a design, the pieces of one body are
named <body>.1 … <body>.N, ordered by centroid, so the tree, tooltips,
forms and picks read as one part with numbered cells.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Meshes that do not tag their element edges with the design's edge names
(tet, hex, blocks) left a selected edge with no highlight while the mesh
was shown. The edge is now marked along its own polyline, which the scene
already draws over the mesh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The design file stores no measure to compare with, so the rebuild's own
failures are the guard: each failed feature lists the bodies it names (all of
them when it names none), and geometry.open replies with a warning per failure,
which the window shows with the open.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
FieldCraft pinned SolidCraft a629236, which predates #1244: a cylinder joined
onto the floor of a closed hollow body (a coplanar touching face) failed to
rebuild there, and the design opened without it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- A solve or a mesher runs as a job with one progress mechanism: the overlay
shows the step, stage, count and elapsed time with a bar when bounded, OK
waits while it runs, and the status sums it up (elements, smallest angle,
time) (#322, #357).
- Over the control channel such a command is a job too: answered when it
ends however long it runs, or at once with wait: false, then job.status,
job.wait, job.cancel; ui.inspect gives job; MCP waits for it (#367).
- A command that cannot run yet lists what it misses in the context panel,
each with a button to the command that provides it (#323).
- A cancelled or refused solve stays in its workspace (#324, test).
- A mesher form starts from the parameters of the mesh it would replace (#343).
- Seed Edges and edge/vertex/face datum points switch the selection filter
while open and restore it (#341).
- Datum forms draw the datum live, the Partition form shows its datum, and
new datums and partitions get the next free name (#347).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The setup checklist marks the mesh Outdated (a warm ⚠ in the browser, with
what changed and where to remesh) when seeds, partitions or datum planes
changed after the last mesher ran, and model.check warns (#342). Replacing
a mesh asks with the element type change it makes, such as tet10 → tet4 (#343).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
solve.heat's reply and the results report give heat_flows: each convection,
flux and source load's heat into the body, the prescribed temperatures'
total and their sum; the results panel lists them for a heat step.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
fieldcraft_model::progress: a host installs a Progress on the worker thread
and reads its snapshot from another; the engine names the step being solved,
the nonlinear solver its load factor, the explicit solver its time, the
fluid solver its steps, transient heat its increments and the tet mesher its
stage and pass. Without one installed every report is a no-op (#322, #357).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A checkbox whose key is unset shows the field's default (#353). An empty JSON
field shows its format hint (#340). Vector components share a line only when
each fits a value such as -12000, else take a line each (#339). A space typed
in a definition name becomes _ and the form says why (#320).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Every command with a schema now refuses a top-level key it does not take,
naming the key and the accepted ones (#316). A bad definition name's error
suggests the nearest valid one (#320). The load and material params docs list
the heat loads and the thermal block.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
A non-zero prescribed displacement is an arrow leaving the nodes along the
motion (its held degrees of freedom stay supports); a prescribed temperature
is a thermometer, convection a wave off the faces, a heat flux an arrow onto
them. In the tree, thermal conditions carry the heat icon and a moving
boundary condition a motion arrow.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
- describe.rs: a definition's fields in its form's labels and units (sets by
members and what they resolve to), for the context panel.
- reply::done: status lines that say what changed ("Showing Load deformed",
"Mode 2: 1637 Hz", "Added material Al").
- The context panel puts the form and the selection above reports; opening
another document clears both; what a form makes is selected.
- Use selection reuses a set with the same members, otherwise names one made
on OK; Cancel leaves the model unchanged. The Target's set row is labelled.
- The browser's state marks sit in one column at its left edge; a right click
selects the row its menu acts on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Ties constrain temperatures with the displacement tie's mortar weights in
steady and transient heat and in coupled temperature-displacement steps; the
heat solver eliminates them with the prescribed temperatures through
constraints::Reduction. refuse_ties is gone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
Delaunay refinement split a boundary face edge at its midpoint even when that
midpoint lay inside the diametral sphere of a feature edge beside it. Each such
split halves the face vertices' distance to the curve, so they piled up against
it (the heated bracket grew face vertices 0.016 mm from a 4 mm-sized edge), the
improvement schedule could not lift the tetrahedra there to its target, and
inserted vertex after vertex around them: 29257 elements and about two minutes
to open instead of 23641 and 6 s. The SolidCraft pin move (4c91f9b) added one
interior vertex to the bracket's end faces, which changed the CDT enough to
expose it.
Following Shewchuk (1998), an encroaching midpoint now splits the encroached
feature edge instead.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
examples.md and mcp.md tell the one-datum workflow and its numbers; the
crank gallery captures and Start card thumbnails are taken again on this
build; ROADMAP marks the automatic blocks of extruded cross-sections done,
and features.md's Decompose entry says what is left (3D parts).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
crank-arm and crank-mirror now take one datum (Sym) and its partition:
mesh.hex.generate extrudes the half CrankArm/a, cutting its cross-section
into blocks itself, with no seeds, and mesh.mirror reflects it. 8 664
hex20, scaled Jacobian min 0.371; root sigma_xx -62.44/+62.44 MPa against
M/Z 62.6 (0.25 %), spindle reaction 1500 N. The seven partitions and
eleven exact seeds go.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
The release job signs SHA256SUMS.txt into SHA256SUMS.txt.minisig with rsign2 when the
FIELDCRAFT_SIGNING_KEY secret exists, and checks the signature against the public key the app
is built with; without the secret the draft is unsigned, the run warns and the notes say the
app cannot install that release itself. docs/releasing.md says how the key is set up, kept
and rotated; docs/updates.md describes checking, verifying and installing, the web app's
Reload to update, and FIELDCRAFT_UPDATE_HOST for tests. privacy.md, control-protocol.md,
web.md and the roadmap say what changed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
